High-Performance High-Speed Steel (HSS-E/PM) • Finishing
Application Data • Series 1N0M JJ
Series 1N0M JJ
Side Milling (A)
and Slotting (B)
A
Material
Group
P
M
K
N
S
Recommended feed per tooth (fz = mm/th) for side milling (A).
For slotting (B), reduce fz by 20%.
TiAlN
B
Cutting Speed — vc
m/min
ap ae ap min
1 1,5 x D 0,5 x D 1 x D 70
2 1,5 x D 0,5 x D 1 x D 60
3 1,5 x D 0,5 x D 1 x D 5 1,5 x D 0,5 x D 1 1,5 x D 0,5 x D 2 1,5 x D
D1 — Diameter
max mm 3,0 4,0 6,0 8,0 10,0 12,0 16,0 20,0 25,0
– 80 fz 0,029 0,039 0,058 0,078 0,090 0,099 0,121 0,137 0,149
– 80 fz 0,029 0,039 0,058 0,078 0,090 0,099 0,121 0,137 0,149
50 – 70 fz 0,024 0,032 0,048 0,065 0,076 0,084 0,105 0,121 0,137
1 x D 25 – 35 fz 0,020 0,026 0,039 0,052 0,061 0,067 0,084 0,097 0,109
1 x D 25 – 35 fz 0,024 0,032 0,048 0,065 0,076 0,084 0,105 0,121 0,137
0,5 x D 1 x D 25 – 30 fz 0,020 0,026 0,039 0,052 0,061 0,067 0,084 0,097 0,109
3 1,5 x D 0,5 x D 1 x D 15 – 20 fz 0,017 0,022 0,033 0,044 0,051 0,056 0,068 0,078 0,085
1 1,5 x D 0,5 x D 1 x D 70 – 80 fz 0,029 0,039 0,058 0,078 0,090 0,099 0,121 0,137 0,149
2 1,5 x D 0,5 x D 1 x D 50 – 70 fz 0,024 0,032 0,048 0,065 0,076 0,084 0,105 0,121 0,137
1 1,5 x D 0,5 x D 1 x D 300 – 375 fz 0,042 0,055 0,079 0,104 0,125 0,144 0,192 0,240 0,300
2 1,5 x D 0,5 x D 1 x D 230 – 300 fz 0,034 0,044 0,063 0,083 0,100 0,115 0,154 0,192 0,240
1 1,5 x D 0,5 x D 1 x D 15 – 30 fz 0,024 0,032 0,048 0,065 0,076 0,084 0,105 0,121 0,137
2 1,5 x D 0,5 x D 0,5 x D 5 – 15 fz 0,013 0,018 0,026 0,034 0,040 0,045 0,056 0,065 0,074
3 1,5 x D 0,5 x D 1 x D 15 – 28 fz 0,020 0,026 0,039 0,052 0,061 0,067 0,084 0,097 0,109
4 1,5 x D 0,5 x D 0,5 x D 15 – 28 fz 0,016 0,022 0,034 0,048 0,056 0,062 0,077 0,089 0,100
Q12
widia.com
NOTE: Lower value of cutting speed is used for high stock removal applications or for higher hardness (machinability) within group.
Higher value of cutting speed is used for finishing applications or for lower hardness (machinability) within group.
Above parameters are based on ideal conditions. For smaller taper machining centres, please adjust parameters accordingly on diameters >12mm.