High-Performance High-Speed Steel (HSS-E/PM) • Finishing
Application Data • Series 1N77 • VariMill ™
Series 1N77 • VariMill
Side Milling (A)
and Slotting (B)
A
Material
Group
P
M
K
N
S
Recommended feed per tooth (fz = mm/th) for side milling (A).
For slotting (B), reduce fz by 20%.
TiCN
B
Cutting Speed — vc
m/min
D1 — Diameter
ap ae ap min max mm 6,0 8,0 10,0 12,0 14,0 16,0 20,0 25,0 30,0
1 1,5 x D 0,5 x D 1 x D 56 – 64 fz 0,058 0,078 0,090 0,099 0,111 0,121 0,137 0,149 0,149
2 1,5 x D 0,5 x D 1 x D 48 – 64 fz 0,058 0,078 0,090 0,099 0,111 0,121 0,137 0,149 0,149
3 1,5 x D 0,5 x D 1 x D 40 – 56 fz 0,048 0,065 0,076 0,084 0,095 0,105 0,121 0,137 0,137
5 1,5 x D 0,5 x D 1 x D 20 – 28 fz 0,039 0,052 0,061 0,067 0,076 0,084 0,097 0,109 0,109
1 1,5 x D 0,5 x D 1 x D 20 – 28 fz 0,048 0,065 0,076 0,084 0,095 0,105 0,121 0,137 0,137
2 1,5 x D 0,5 x D 1 x D 20 – 24 fz 0,039 0,052 0,061 0,067 0,076 0,084 0,097 0,109 0,109
3 1,5 x D 0,5 x D 1 x D 12 – 16 fz 0,033 0,044 0,051 0,056 0,062 0,068 0,078 0,085 0,085
1 1,5 x D 0,5 x D 1 x D 56 – 64 fz 0,058 0,078 0,090 0,099 0,111 0,121 0,137 0,149 0,149
2 1,5 x D 0,5 x D 1 x D 40 – 56 fz 0,048 0,065 0,076 0,084 0,095 0,105 0,121 0,137 0,137
1 1,5 x D 0,5 x D 1 x D 240 – 300 fz 0,079 0,104 0,125 0,144 0,168 0,192 0,240 0,300 0,300
2 1,5 x D 0,5 x D 1 x D 184 – 240 fz 0,063 0,083 0,100 0,115 0,134 0,154 0,192 0,240 0,240
1 1,5 x D 0,5 x D 1 x D 12 – 24 fz 0,048 0,065 0,076 0,084 0,095 0,105 0,121 0,137 0,137
2 1,5 x D 0,5 x D 1 x D 4 – 12 fz 0,026 0,034 0,040 0,045 0,050 0,056 0,065 0,074 0,074
3 1,5 x D 0,5 x D 1 x D 12 – 22 fz 0,039 0,052 0,061 0,067 0,076 0,084 0,097 0,109 0,109
4 1,5 x D 0,5 x D 0,5 x D 12 – 22 fz 0,034 0,048 0,056 0,062 0,070 0,077 0,089 0,100 0,100
widia.com
Q13
High-Performance
NOTE: Lower value of cutting speed is used for high stock removal applications or for higher hardness (machinability) within group.
Higher value of cutting speed is used for finishing applications or for lower hardness (machinability) within group.
Above parameters are based on ideal conditions. For smaller taper machining centres, please adjust parameters accordingly on diameters >12mm.