High-Performance High-Speed Steel (HSS-E/PM) • Roughing
Application Data • Series 6N70
Series 6N70
Side Milling (A)
and Slotting (B)
A
Material
Group
P
M
K
S
Recommended feed per tooth (fz = mm/th) for side milling (A).
For slotting (B), reduce fz by 20%.
TiAlN
B
Cutting Speed — vc
m/min
ap ae ap min
D1 — Diameter
max mm 6,0 8,0 10,0 12,0 16,0 18,0 20,0 25,0 32,0
1 1,5 x D 0,5 x D 1 x D 70 – 80 fz 0,058 0,078 0,090 0,099 0,121 0,130 0,137 0,149 0,190
2 1,5 x D 0,5 x D 1 x D 60 – 80 fz 0,058 0,078 0,090 0,099 0,121 0,130 0,137 0,149 0,190
3 1,5 x D 0,5 x D 1 x D 50 – 70 fz 0,048 0,065 0,076 0,084 0,105 0,113 0,121 0,137 0,175
5 1,5 x D 0,5 x D 1 x D 25 – 35 fz 0,039 0,052 0,061 0,067 0,084 0,091 0,097 0,109 0,140
1 1,5 x D 0,5 x D 1 x D 25 – 35 fz 0,048 0,065 0,076 0,084 0,105 0,113 0,121 0,137 0,175
2 1,5 x D 0,5 x D 1 x D 25 – 30 fz 0,039 0,052 0,061 0,067 0,084 0,091 0,097 0,109 0,140
3 1,5 x D 0,5 x D 1 x D 15 – 20 fz 0,033 0,044 0,051 0,056 0,068 0,073 0,078 0,085 0,109
1 1,5 x D 0,5 x D 1 x D 70 – 80 fz 0,058 0,078 0,090 0,099 0,121 0,130 0,137 0,149 0,190
2 1,5 x D 0,5 x D 1 x D 50 – 70 fz 0,048 0,065 0,076 0,084 0,105 0,113 0,121 0,137 0,175
1 1,5 x D 0,5 x D 1 x D 15 – 30 fz 0,048 0,065 0,076 0,084 0,105 0,113 0,121 0,137 0,175
2 1,5 x D 0,5 x D 1 x D 5 – 15 fz 0,026 0,034 0,040 0,045 0,056 0,060 0,065 0,074 0,094
3 1,5 x D 0,5 x D 1 x D 15 – 30 fz 0,039 0,052 0,061 0,067 0,084 0,091 0,097 0,109 0,140
4 1,5 x D 0,5 x D 1 x D 15 – 30 fz 0,034 0,048 0,056 0,062 0,077 0,083 0,089 0,100 0,128
NOTE: Lower value of cutting speed is used for high stock removal applications or for higher hardness (machinability) within group.
Higher value of cutting speed is used for fi nishing applications or for lower hardness (machinability) within group.
Above parameters are based on ideal conditions. For smaller taper machining centres, please adjust parameters accordingly on diameters >12mm.
Application Data • Series 6NL6
A
Material
Group
P
M
K
S
Recommended feed per tooth (fz = mm/th) for side milling (A).
For slotting (B), reduce fz by 20%.
TiAlN
B
Cutting Speed — vc
m/min
D1 — Diameter
ap ae ap min max mm 10,0 12,0 16,0 20,0 25,0
1 1,5 x D 0,5 x D 1 x D 70 – 80 fz 0,063 0,070 0,085 0,096 0,104
2 1,5 x D 0,5 x D 1 x D 60 – 80 fz 0,063 0,070 0,085 0,096 0,104
3 1,5 x D 0,5 x D 1 x D 50 – 70 fz 0,053 0,059 0,073 0,085 0,096
5 1,5 x D 0,5 x D 1 x D 25 – 35 fz 0,042 0,047 0,059 0,068 0,076
1 1,5 x D 0,5 x D 1 x D 25 – 35 fz 0,053 0,059 0,073 0,085 0,096
2 1,5 x D 0,5 x D 1 x D 25 – 30 fz 0,042 0,047 0,059 0,068 0,076
3 1,5 x D 0,5 x D 1 x D 15 – 20 fz 0,035 0,039 0,048 0,054 0,060
1 1,5 x D 0,5 x D 1 x D 70 – 80 fz 0,063 0,070 0,085 0,096 0,104
2 1,5 x D 0,5 x D 1 x D 50 – 70 fz 0,053 0,059 0,073 0,085 0,096
1 1,5 x D 0,5 x D 1 x D 15 – 30 fz 0,053 0,059 0,073 0,085 0,096
2 1,5 x D 0,5 x D 1 x D 5 – 15 fz 0,028 0,031 0,039 0,045 0,051
3 1,5 x D 0,5 x D 1 x D 15 – 30 fz 0,042 0,047 0,059 0,068 0,076
4 1,5 x D 0,5 x D 1 x D 10 – 20 fz 0,039 0,043 0,054 0,062 0,070
NOTE: Lower value of cutting speed is used for high stock removal applications or for higher hardness (machinability) within group.
Higher value of cutting speed is used for fi nishing applications or for lower hardness (machinability) within group.
Above parameters are based on ideal conditions. For smaller taper machining centres, please adjust parameters accordingly on diameters >12mm.
widia.com
Q11
Side Milling (A)
and Slotting (B)
High-Performance
Series 6NL6