OSAWA - katalog | KL-TECH s.r.o. | www.klte.cz

KL-TECH s.r.o | www.klte.cz TYPHOON - high performance solid carbide drills CUTTING PARAMETERS INFO 3530HL Material Group ISO 513 Ø RUN OUT <0.02mm P1 P2 P3 P4 P5 P6 TYPHOO N TA-HTA-4 HTA Hardness/Rm 500-700 N/mm² 600-1000 N/mm² 900-1200 N/mm² 1200-1400 N/mm² Vc (m/min) 50-70 40-60 30-50 25-35 D (mm) n (rpm) 3.0 3.5 4.0 4.5 5.0 5.5 6.0 6.5 7.0 7.5 8.0 6370 5460 4780 4250 3820 3470 3180 2940 2730 2550 2390 Material Group ISO 513 Ø RUN OUT <0.02mm fn Vf (mm/rev) (mm/min) 0.046 0.053 0.063 0.074 0.084 0.095 0.105 0.116 0.126 0.137 0.147 M1 290 287 301 312 321 328 334 340 344 348 351 n (rpm) 5310 4550 3980 3540 3180 2900 2650 2450 2270 2120 1990 M2 fn Vf (mm/rev) (mm/min) 0.041 0.047 0.057 0.066 0.076 0.085 0.095 0.104 0.113 0.123 0.132 220 210 230 230 240 250 250 250 260 260 260 n (rpm) 4250 3640 3180 2830 2550 2320 2120 1960 1820 1700 1590 fn Vf (mm/rev) (mm/min) 0.036 0.042 0.050 0.059 0.067 0.076 0.084 0.092 0.101 0.109 0.118 150 150 160 170 170 180 180 180 180 190 190 n (rpm) 3180 2730 2390 2120 1910 1740 1590 1470 1360 1270 1190 fn Vf (mm/rev) (mm/min) 0.032 0.037 0.044 0.051 0.059 0.066 0.074 0.081 0.088 0.096 0.103 M3 M4 M5 100 100 110 110 110 120 120 120 120 120 120 < 750 N/mm² 550-850 N/mm² 650-950 N/mm² 850-1200 N/mm² Vc (m/min) 35-45 25-35 20-30 15-25 n (rpm) 3.0 3.5 4.0 4.5 5.0 5.5 6.0 6.5 7.0 7.5 8.0 4250 3640 3180 2830 2550 2320 2120 1960 1820 1700 1590 fn Vf (mm/rev) (mm/min) 0.034 0.039 0.047 0.055 0.063 0.071 0.079 0.087 0.095 0.102 0.110 150 140 150 160 160 160 170 170 170 170 180 n (rpm) 3180 2730 2390 2120 1910 1740 1590 1470 1360 1270 1190 fn Vf (mm/rev) (mm/min) 0.029 0.033 0.040 0.047 0.054 0.060 0.067 0.074 0.080 0.087 0.094 90 90 100 100 100 100 110 110 110 110 110 n (rpm) 2650 2270 1990 1770 1590 1450 1330 1220 1140 1060 1000 fn Vf (mm/rev) (mm/min) 0.024 0.028 0.033 0.039 0.044 0.050 0.055 0.061 0.066 0.072 0.077 63 63 66 68 70 70 70 70 80 80 80 n (rpm) 2120 1820 1590 1420 1270 1160 1060 980 910 850 800 TYPHOO N SUH TYPHOO N ALH TYPHOO N HRC TYPHOO N SUH MIN I TYPHOO N HL Hardness/Rm D (mm) TYPHOO N PU-HPU C-SD-TA fn Vf (mm/rev) (mm/min) 0.020 0.024 0.028 0.033 0.038 0.043 0.047 0.052 0.057 0.061 0.066 43 43 45 47 48 49 50 51 52 52 53 LFTA SUTA HSS-HSS /CO DRILLS G2 MDTA HF VH/U P MEF ALU MEX UH HSS/CO -HSSP END MIL LS CARBIDE BURRS 195

OSAWA - katalog | KL-TECH s.r.o. | www.klte.cz | Page 197