African Mining October 2025 | Page 29

HEALTH AND SAFETY •
Mistracking after the head pulley Mistracking just after the head pulley on the conveyor’ s return has two main causes. The first might be that the lagging is missing on one end of the pulley, so the pulley’ s diameter is off-centre, placing uneven pressure on the belt and causing it to wander. If this is not the case, then the belt cleaning system may have been mounted slightly askew, putting greater pressure on one side of the belt and pulley. This uneven friction can also lead to mistracking.
Figure 3: Contact with the support structure can cause serious belt damage.
collects lumps of spilled material on the non-carrying side. If these objects are not removed, they can become trapped between the tail pulley and the belt, causing mistracking and often doing significant damage to both.
• Uneven discharge – as the belt drifts to either side of the head pulley, the belt cleaners do not properly clean the entire surface, causing excessive carryback. Material collects on the pulleys and structure, fouling the return side of the belt, resulting in slippage, lost product and other negative effects.
• Uneven loading – if the belt path leading from the tail pulley into the loading zone is uneven, the cargo can be loaded offcentre and cause excessive spillage. This may also be caused by inadequate transfer point design.
Identification begins at the head pulley Starting at the head pulley, the belt should also be inspected for cupping, bow / camber( a long curvature) or crooked splicing. When observing the empty belt running over the head pulley, a cambered belt will drift to one side in the middle of the camber and then slowly return to centre as the belt travels through the head pulley. If a splice is crooked, the belt’ s path will jump quickly to one side as the splice travels over the pulley.
If it is discovered that these factors are the cause of mistracking, simply adjusting the conveyor’ s rolling components will not correct the issue. The only options are either replacing the entire belt, or – in the case of crooked splice( s) – re-splicing the belt, assuming there is enough extra belting in the take-up system to allow removal of the faulty splice section.
Once the type of misalignment has been identified, the cause can be sought. There are three groups of common causes for mistracking. The first is a fault with the belt or splice, second is the conveyor’ s structure, components or environment, and third is due to improper material loading.”
Belt and splice If the belt is poorly manufactured or stored improperly, it can bow or camber. Poor installation of a vulcanised or mechanical splice can result in a splice that causes belt tracking problems. Exposure to the elements or to chemicals can degrade the carcass( plies or cords) and the cover of the belt. Faults and damage caused by mismatching the belt to the application and / or operating environment can require frequent replacement.
Conveyor structure Inaccurate alignment of the conveyor stringer structure can have subtle but lasting effects on the belt’ s performance. Structural misalignment can happen due to age, machinery collisions, seismic activity effects or ground settling.
Environmental factors High winds require“ wind loops” to keep the belt in line. Exposure to extreme temperatures on one side of the conveyor can make components expand, causing changes in friction.
Improper loading The load’ s centre of gravity will seek the lowest point of the troughing idlers, so if the belt is not centre loaded, the weight of the cargo pushes the belt toward the conveyor’ s more lightly-loaded side( Figure 4).
Belt training A common procedure to correct the wandering belt is to slightly adjust the return and carrying idlers against the direction of
During the observation procedure, if the belt moves to one side and stays there, the problem may be one of three things: the head pulley lagging is not consistent, the last few carrying idlers prior to the pulley are out of alignment or the head pulley itself is not properly adjusted.
By focusing solely on belt alignment, plant personnel may miss other opportunities to increase performance and relieve some of the burden on their system.
Figure 4: Off-centre loading can be a root cause of belt mistracking with the cargo weight typically pushing the belt toward the more lightlyloaded side.
www. africanmining. co. za African Mining Publication African Mining African Mining • October 2025 • 27