High-Performance Solid Carbide End Mills • Roughing
Application Data • Series 4U40 • Victory ™ Grades
Series 4U40 • Victory Grades
Material
Group
P
M
K
S
H
B Cutting Speed — vc
m/min
D1 — Diameter
ap ae ap min max mm 6,0 8,0 10,0 12,0 16,0 20,0 25,0
3 0,8 x D 0,5 x D 0,75 x D 120 – 160 fz 0,036 0,050 0,061 0,070 0,087 0,101 0,114
4 0,8 x D 0,4 x D 0,5 x D 90 – 150 fz 0,033 0,045 0,054 0,062 0,077 0,088 0,098
5 0,8 x D 0,5 x D 0,75 x D 60 – 100 fz 0,029 0,040 0,048 0,056 0,070 0,081 0,091
6 0,8 x D 0,4 x D 0,5 x D 50 – 75 fz 0,025 0,034 0,040 0,047 0,057 0,065 0,071
1 0,8 x D 0,5 x D 0,75 x D 90 – 115 fz 0,036 0,050 0,061 0,070 0,087 0,101 0,114
2 0,8 x D 0,4 x D 0,75 x D 60 – 80 fz 0,029 0,040 0,048 0,056 0,070 0,081 0,091
3 0,8 x D 0,4 x D 0,75 x D 60 – 70 fz 0,025 0,034 0,040 0,047 0,057 0,065 0,071
1 0,8 x D 0,5 x D 0,75 x D 120 – 150 fz 0,044 0,060 0,072 0,083 0,101 0,114 0,124
2 0,8 x D 0,5 x D 0,75 x D 110 – 140 fz 0,036 0,050 0,061 0,070 0,087 0,101 0,114
3 0,8 x D 0,4 x D 0,75 x D 110 – 130 fz 0,029 0,040 0,048 0,056 0,070 0,081 0,091
1 0,8 x D 0,4 x D 0,75 x D 50 – 90 fz 0,036 0,050 0,061 0,070 0,087 0,101 0,114
2 0,8 x D 0,25 x D 0,3 x D 25 – 40 fz 0,019 0,026 0,032 0,037 0,046 0,054 0,061
3 0,8 x D 0,4 x D 0,75 x D 60 – 80 fz 0,029 0,040 0,048 0,056 0,070 0,081 0,091
4 0,8 x D 0,3 x D 0,5 x D 50 – 60 fz 0,026 0,037 0,045 0,052 0,064 0,074 0,084
1 0,8 x D 0,5 x D 0,5 x D 80 – 140 fz 0,033 0,045 0,054 0,062 0,077 0,088 0,098
2 0,8 x D 0,2 x D 0,3 x D 70 – 120 fz 0,025 0,034 0,040 0,047 0,057 0,065 0,071
3 0,8 x D 0,15 x D 0,2 x D 60 – 90 fz 0,019 0,026 0,032 0,037 0,046 0,054 0,061
NOTE: Lower value of cutting speed is used for high stock removal applications or for higher hardness (machinability) within group.
Higher value of cutting speed is used for finishing applications or for lower hardness (machinability) within group.
For rougher tool with 6 flutes, use ap in slotting 60% of table value.
Above parameters are based on ideal conditions. For smaller taper machining centres, please adjust parameters accordingly on >12mm diameters.
widia.com
O73
A
Recommended feed per tooth (fz = mm/th) for side milling (A).
For slotting (B), reduce fz by 20%.
WP15PE
Side Milling (A)
and Slotting (B)