High-Performance Solid Carbide End Mills • Roughing
Application Data • Series 422820 422824
Series 422820 422824
Side Milling (A)
and Slotting (B)
K30F-DCHP
Recommended feed per tooth (fz = mm/th) for side milling (A).
For slotting (B), reduce fz by 20%.
AlTiN
A
Material
Group
Cutting Speed — vc
m/min
ap min
mm 6,0
– 200 fz – 190 fz 120 – 160 0,25 x D 90 – 0,25 x D 60 – 0,25 x D 0,25 x D 50 3 x D 0,25 x D 0,5 x D 3 x D 0,25 x D 0,5 x D 1 3 x D 0,25 x D 2 3 x D 3 3 x D S 1 H 1
M
K
ap ae 1 3 x D 0,25 x D 0,7 x D 150
2 3 x D 0,25 x D 0,5 x D 140
3 3 x D 0,25 x D 0,5 x D 4 3 x D 0,25 x D 5 3 x D 0,25 x D 6 3 x D 1 3
D1 — Diameter
max
P
8,0 10,0 12,0 16,0 20,0 25,0
0,032 0,043 0,052 0,063 0,077 0,087 0,095
0,032 0,043 0,052 0,063 0,077 0,087 0,095
fz 0,026 0,036 0,044 0,054 0,067 0,077 0,087
150 fz 0,024 0,032 0,039 0,048 0,059 0,067 0,075
100 fz 0,021 0,029 0,035 0,043 0,053 0,062 0,070
– 75 fz 0,018 0,024 0,029 0,036 0,044 0,050 0,054
80 – 100 fz 0,026 0,036 0,044 0,054 0,067 0,077 0,087
60 – 80 fz 0,018 0,024 0,029 0,036 0,044 0,050 0,054
0,5 x D 120 – 160 fz 0,032 0,043 0,052 0,063 0,077 0,087 0,095
0,25 x D 0,5 x D 110 – 140 fz 0,026 0,036 0,044 0,054 0,067 0,077 0,087
0,25 x D 0,5 x D 100 – 130 fz 0,021 0,029 0,035 0,043 0,053 0,062 0,070
3 x D 0,25 x D 0,5 x D 50 – 90 fz 0,026 0,036 0,044 0,054 0,067 0,077 0,087
3 x D 0,25 x D 0,5 x D 80 – 140 fz 0,024 0,032 0,039 0,048 0,059 0,067 0,075
NOTE: Lower value of cutting speed is used for high stock removal applications or for higher hardness (machinability) within group.
Higher value of cutting speed is used for finishing applications or for lower hardness (machinability) within group.
Above parameters are based on ideal conditions. For smaller taper machining centres, please adjust parameters accordingly on >12mm diameters.
O72
widia.com
B