General Purpose Solid Carbide End Mills • Roughing / Finishing Application Data • Series D014 2528 4014 4024 • VariMill ™ GP
��Series D014 2528 4014 4024 • TiAlN • VariMill GP
Material Group
P
M
K
Side Milling( A) TiAlN Recommended feed per tooth( fz = mm / th) for side milling( A).
A |
Cutting Speed— vc m / min |
D1— Diameter |
ap |
ae |
min |
max |
mm |
2,0 |
3,0 |
4,0 |
5,0 |
6,0 |
8,0 |
10,0 |
12,0 |
14,0 |
16,0 |
18,0 |
20,0 |
0 |
Ap1 max |
0,1 x D |
150 |
– |
200 |
fz |
0,014 |
0,021 |
0,028 |
0,036 |
0,044 |
0,060 |
0,072 |
0,083 |
0,092 |
0,101 |
0,108 |
0,114 |
1 |
Ap1 max |
0,1 x D |
150 |
– |
200 |
fz |
0,014 |
0,021 |
0,028 |
0,036 |
0,044 |
0,060 |
0,072 |
0,083 |
0,092 |
0,101 |
0,108 |
0,114 |
2 |
Ap1 max |
0,1 x D |
140 |
– |
190 |
fz |
0,014 |
0,021 |
0,028 |
0,036 |
0,044 |
0,060 |
0,072 |
0,083 |
0,092 |
0,101 |
0,108 |
0,114 |
3 |
Ap1 max |
0,1 x D |
120 |
– |
160 |
fz |
0,011 |
0,017 |
0,023 |
0,030 |
0,036 |
0,050 |
0,061 |
0,070 |
0,079 |
0,087 |
0,095 |
0,101 |
4 |
Ap1 max |
0,1 x D |
90 |
– |
150 |
fz |
0,010 |
0,016 |
0,021 |
0,027 |
0,033 |
0,045 |
0,054 |
0,062 |
0,070 |
0,077 |
0,083 |
0,088 |
1 Ap1 max 0, 1 x D 90 – 115 fz 0, 011 0, 017 0, 023 0, 030 0, 036 0, 050 0, 061 0, 070 0, 079 0, 087 0, 095 0, 101 2 Ap1 max 0,1 x D 60 – 80 fz 0,009 0,014 0,019 0,024 0,029 0,040 0,048 0,056 0,063 0,070 0,076 0,081 1 Ap1 max 0,1 x D 120 – 150 fz 0,014 0,021 0,028 0,036 0,044 0,060 0,072 0,083 0,092 0,101 0,108 0,114 2 Ap1 max 0,1 x D 110 – 140 fz 0,011 0,017 0,023 0,030 0,036 0,050 0,061 0,070 0,079 0,087 0,095 0,101
NOTE: Lower value of cutting speed is used for high stock removal applications or for higher hardness( machinability) within group. Higher value of cutting speed is used for finishing applications or for lower hardness( machinability) within group. Above parameters are based on ideal conditions. For smaller taper machining centres, please adjust parameters accordingly on > 12mm diameters.
��Series D014 2528 4014 4024 • Uncoated • VariMill GP
Material Group
P
Side Milling( A) uncoated Recommended feed per tooth( fz = mm / th) for side milling( A). Cutting Speed— vc
A D1— Diameter m / min ap ae min max mm 3,0 4,0 6,0 8,0 10,0 12,0 16,0 20,0
0 |
Ap1 max |
0,1 x D |
120 |
– |
160 |
fz |
0,021 |
0,028 |
0,044 |
0,060 |
0,072 |
0,083 |
0,101 |
0,114 |
1 |
Ap1 max |
0,1 x D |
120 |
– |
160 |
fz |
0,021 |
0,028 |
0,044 |
0,060 |
0,072 |
0,083 |
0,101 |
0,114 |
2 |
Ap1 max |
0,1 x D |
112 |
– |
152 |
fz |
0,021 |
0,028 |
0,044 |
0,060 |
0,072 |
0,083 |
0,101 |
0,114 |
NOTE: Lower value of cutting speed is used for high stock removal applications or for higher hardness( machinability) within group. Higher value of cutting speed is used for finishing applications or for lower hardness( machinability) within group. Above parameters are based on ideal conditions. For smaller taper machining centres, please adjust parameters accordingly on > 12mm diameters.
General Purpose Solid Carbide End Mills widia. com P41
KL-TECH s. r. o. | www. klte. cz