High-Performance Solid Carbide End Mills • Finishing
Application Data • Series 422822 422826
Series 422822 422826
K30F-DCF
Side Milling (A)
and Slotting (B)
Cutting Speed — vc
m/min
A
Material
Group
P
M
N
S
H
D1 — Diameter
ap ae min – max mm 6,0 8,0 10,0 12,0 14,0 16,0 18,0 20,0 25,0
0 1,5 x D 0,05 x D 165 – 165 fz 0,044 0,060 0,072 0,083 0,092 0,101 0,108 0,114 0,124
1 1,5 x D 0,05 x D 165 – 165 fz 0,044 0,060 0,072 0,083 0,092 0,101 0,108 0,114 0,124
2 1,5 x D 0,05 x D 154 – 154 fz 0,044 0,060 0,072 0,083 0,092 0,101 0,108 0,114 0,124
3 1,5 x D 0,05 x D 132 – 132 fz 0,036 0,050 0,061 0,070 0,079 0,087 0,095 0,101 0,114
4 1,5 x D 0,05 x D 99 – 99 fz 0,033 0,045 0,054 0,062 0,070 0,077 0,083 0,088 0,098
5 1,5 x D 0,05 x D 66 – 66 fz 0,029 0,040 0,048 0,056 0,063 0,070 0,076 0,081 0,091
6 1,5 x D 0,04 x D 55 – 55 fz 0,025 0,034 0,040 0,047 0,052 0,057 0,061 0,065 0,071
1 1,5 x D 0,05 x D 99 – 99 fz 0,036 0,050 0,061 0,070 0,079 0,087 0,095 0,101 0,114
2 1,5 x D 0,05 x D 66 – 66 fz 0,029 0,040 0,048 0,056 0,063 0,070 0,076 0,081 0,091
3 1,5 x D 0,05 x D 66 – 66 fz 0,025 0,034 0,040 0,047 0,052 0,057 0,061 0,065 0,071
1 1,5 x D 0,05 x D 132 – 132 fz 0,044 0,060 0,072 0,083 0,092 0,101 0,108 0,114 0,124
2 1,5 x D 0,05 x D 121 – 121 fz 0,036 0,050 0,061 0,070 0,079 0,087 0,095 0,101 0,114
3 1,5 x D 0,05 x D 121 – 121 fz 0,029 0,040 0,048 0,056 0,063 0,070 0,076 0,081 0,091
1 1,5 x D 0,05 x D 275 – 275 fz 0,054 0,072 0,090 0,108 0,126 0,144 0,162 0,180 0,225
1 1,5 x D 0,04 x D 55 – 55 fz 0,036 0,050 0,061 0,070 0,079 0,087 0,095 0,101 0,114
2 1,5 x D 0,04 x D 27.5 – 27.5 fz 0,019 0,026 0,032 0,037 0,042 0,046 0,050 0,054 0,061
3 1,5 x D 0,05 x D 66 – 66 fz 0,029 0,040 0,048 0,056 0,063 0,070 0,076 0,081 0,091
4 1,5 x D 0,05 x D 55 – 55 fz 0,026 0,037 0,045 0,052 0,058 0,064 0,069 0,074 0,084
1 1,5 x D 0,04 x D 88 – 88 fz 0,033 0,045 0,054 0,062 0,070 0,077 0,083 0,088 0,098
NOTE: Lower value of cutting speed is used for high stock removal applications or for higher hardness (machinability) within group.
Higher value of cutting speed is used for finishing applications or for lower hardness (machinability) within group.
Above parameters are based on ideal conditions. For smaller taper machining centres, please adjust parameters accordingly on >12mm diameters.
O108
widia.com
K
Recommended feed per tooth (fz = mm/th) for side milling (A).
For slotting (B), reduce fz by 20%.
AlTiN