High-Performance Solid Carbide End Mills • Finishing
Application Data • Series D517 • Victory ™ Grades
Series D517 • Victory Grades
M
K
S
H
Recommended feed per tooth (fz = mm/th) for side milling (A).
A
D1 — Diameter
ap ae min max mm 4,0 6,0 8,0 10,0 12,0 14,0 16,0 18,0 20,0
0 Ap1 max 0,05 x D 150 – 200 fz 0,028 0,044 0,060 0,072 0,083 0,092 0,101 0,108 0,114
1 Ap1 max 0,05 x D 150 – 200 fz 0,028 0,044 0,060 0,072 0,083 0,092 0,101 0,108 0,114
2 Ap1 max 0,05 x D 140 – 190 fz 0,028 0,044 0,060 0,072 0,083 0,092 0,101 0,108 0,114
3 Ap1 max 0,05 x D 120 – 160 fz 0,023 0,036 0,050 0,061 0,070 0,079 0,087 0,095 0,101
4 Ap1 max 0,05 x D 90 – 150 fz 0,021 0,033 0,045 0,054 0,062 0,070 0,077 0,083 0,088
5 Ap1 max 0,05 x D 60 – 100 fz 0,019 0,029 0,040 0,048 0,056 0,063 0,070 0,076 0,081
6 Ap1 max 0,05 x D 50 – 75 fz 0,016 0,025 0,034 0,040 0,047 0,052 0,057 0,061 0,065
1 Ap1 max 0,05 x D 90 – 115 fz 0,023 0,036 0,050 0,061 0,070 0,079 0,087 0,095 0,101
2 Ap1 max 0,05 x D 60 – 80 fz 0,019 0,029 0,040 0,048 0,056 0,063 0,070 0,076 0,081
3 Ap1 max 0,05 x D 60 – 70 fz 0,016 0,025 0,034 0,040 0,047 0,052 0,057 0,061 0,065
1 Ap1 max 0,05 x D 120 – 150 fz 0,028 0,044 0,060 0,072 0,083 0,092 0,101 0,108 0,114
2 Ap1 max 0,05 x D 110 – 140 fz 0,023 0,036 0,050 0,061 0,070 0,079 0,087 0,095 0,101
3 Ap1 max 0,05 x D 110 – 130 fz 0,019 0,029 0,040 0,048 0,056 0,063 0,070 0,076 0,081
1 Ap1 max 0,04 x D 50 – 90 fz 0,023 0,036 0,050 0,061 0,070 0,079 0,087 0,095 0,101
2 Ap1 max 0,04 x D 25 – 40 fz 0,013 0,019 0,026 0,032 0,037 0,042 0,046 0,050 0,054
3 Ap1 max 0,05 x D 60 – 80 fz 0,019 0,029 0,040 0,048 0,056 0,063 0,070 0,076 0,081
4 Ap1 max 0,05 x D 50 – 60 fz 0,016 0,026 0,037 0,045 0,052 0,058 0,064 0,069 0,074
1 Ap1 max 0,04 x D 80 – 140 fz 0,021 0,033 0,045 0,054 0,062 0,070 0,077 0,083 0,088
NOTE: Lower value of cutting speed is used for high stock removal applications or for higher hardness (machinability) within group.
Higher value of cutting speed is used for finishing applications or for lower hardness (machinability) within group.
For better surface finish, reduce feed per tooth.
widia.com
O107
P
WP15PE
Cutting Speed — vc
m/min
Material
Group
Side Milling (A)