OSAWA - katalog | KL-TECH s.r.o. | www.klte.cz

KL-TECH s.r.o | www.klte.cz G2 - General purpose - Corner radius CUTTING PARAMETERS INFO G2CS2R N TYPHOO HTA TA-HTA-4 Material Group ISO 513 N TYPHOO PU-HPU P2 P3 K1 P4 M1 M2 P5 K2 M3 700-1000 N/mm² < 40 HRC ap x ae 0.5D x D 0.5D x D 0.5D x D Vc (m/min) 80-100 50-70 30-50 N TYPHOO ALH N TYPHOO HRC D (mm) n (rpm) fn Vf (mm/rev) (mm/min) 1 2 3 4 5 6 8 10 12 28660 14330 9550 7170 5730 4780 3580 2870 2390 0.004 0.008 0.012 0.016 0.020 0.025 0.032 0.038 0.045 230 230 230 230 230 240 230 220 220 n (rpm) fn Vf (mm/rev) (mm/min) 19110 9550 6370 4780 3820 3180 2390 1910 1590 0.003 0.007 0.010 0.014 0.017 0.021 0.027 0.032 0.038 130 130 130 130 130 140 130 120 120 n (rpm) N1 K3 < 700 N/mm² SLOTTING N2 N3 N4 0.5D x D 100-120 fn Vf (mm/rev) (mm/min) 12740 6370 4250 3180 2550 2120 1590 1270 1060 0.003 0.006 0.009 0.012 0.015 0.019 0.024 0.029 0.034 80 80 80 80 80 80 80 70 70 n (rpm) fn Vf (mm/rev) (mm/min) 35030 17520 11680 8760 7010 5840 4380 3500 2920 0.005 0.010 0.016 0.021 0.026 0.033 0.042 0.049 0.059 360 360 360 360 360 380 360 350 340 < D3 mm: ap = 0.2D Material Group ISO 513 N TYPHOO HL C-SD-TA P1 P2 P3 K1 P4 M1 M2 P5 K2 M3 < 700 N/mm² 700-1000 N/mm² < 40 HRC ap x ae 1.5D x 0.5D 1.5D x 0.5D 1.5D x 0.5D Vc (m/min) 80-100 50-70 30-50 SIDE MILLING SUTA /CO HSS-HSS DRILLS D (mm) n (rpm) fn Vf (mm/rev) (mm/min) 1 2 3 4 5 6 8 10 12 28660 14330 9550 7170 5730 4780 3580 2870 2390 0.005 0.010 0.014 0.019 0.024 0.030 0.038 0.046 0.054 280 280 280 280 280 290 270 260 260 n (rpm) fn Vf (mm/rev) (mm/min) 19110 9550 6370 4780 3820 3180 2390 1910 1590 0.004 0.008 0.012 0.016 0.020 0.026 0.033 0.039 0.046 160 160 160 160 160 160 160 150 150 n (rpm) N1 K3 Hardness/Rm LFTA G2 Hardness/Rm N TYPHOO SUH N TYPHOO I SUH MIN P1 N2 N3 N4 1.5D x 0.5D 100-120 fn Vf (mm/rev) (mm/min) 12740 6370 4250 3180 2550 2120 1590 1270 1060 0.004 0.007 0.011 0.014 0.018 0.023 0.029 0.034 0.041 90 90 90 90 90 100 90 90 90 n (rpm) fn Vf (mm/rev) (mm/min) 35030 17520 11680 8760 7010 5840 4380 3500 2920 0.006 0.012 0.019 0.025 0.031 0.039 0.050 0.059 0.070 440 440 440 440 440 460 440 410 410 < D3 mm: ae = 0.2D Material Group ISO 513 P1 P2 P3 K1 P4 M1 M2 P5 K2 M3 N1 K3 N2 N3 N4 MDTA P HF VH/U MEF Hardness/Rm < 700 N/mm² 700-1000 N/mm² < 40 HRC ap x ae D x D D x D 0.5D x D D x D Vc (m/min) 70-90 40-60 25-35 80-100 DRILLING ALU MEX < D3 mm: ap = 0.5D UH -HSSP HSS/CO LS END MIL CARBIDE BURRS 350 D (mm) n (rpm) 1 2 3 4 5 6 8 10 12 25480 12740 8490 6370 5100 4250 3180 2550 2120 fn Vf (mm/rev) (mm/min) 0.002 0.005 0.007 0.010 0.012 0.015 0.019 0.023 0.027 120 120 120 120 120 130 120 120 110 n (rpm) 15920 7960 5310 3980 3180 2650 1990 1590 1330 fn Vf (mm/rev) (mm/min) 0.002 0.004 0.006 0.008 0.010 0.013 0.016 0.019 0.023 60 60 60 60 60 70 60 60 60 n (rpm) 9550 4780 3180 2390 1910 1590 1190 960 800 fn Vf (mm/rev) (mm/min) 0.002 0.004 0.005 0.007 0.009 0.011 0.014 0.017 0.020 30 30 30 30 30 40 30 30 30 n (rpm) 28660 14330 9550 7170 5730 4780 3580 2870 2390 fn Vf (mm/rev) (mm/min) 0.003 0.006 0.009 0.012 0.016 0.020 0.025 0.030 0.035 180 180 180 180 180 190 180 170 170

OSAWA - katalog | KL-TECH s.r.o. | www.klte.cz | Página 352