OSAWA - katalog | KL-TECH s.r.o. | www.klte.cz

KL-TECH s.r.o | www.klte.cz G2 - General purpose - Square CUTTING PARAMETERS INFO G2CS4 N TYPHOO HTA TA-HTA-4 Material Group ISO 513 N TYPHOO PU-HPU P MEF ALU MEX UH -HSSP HSS/CO LS END MIL CARBIDE BURRS 338 M1 M2 P5 K2 M3 1.5D x 0.2D 1.5D x 0.2D 80-100 50-70 30-50 D (mm) n (rpm) 1 2 3 4 5 6 8 10 12 14 16 18 20 22 25 28660 14330 9550 7170 5730 4780 3580 2870 2390 2050 1790 1590 1430 1300 1150 fn Vf (mm/rev) (mm/min) 0.004 0.007 0.010 0.013 0.016 0.019 0.025 0.032 0.040 0.047 0.054 0.060 0.065 0.073 0.083 400 400 380 370 370 360 360 370 380 390 390 380 370 380 380 n (rpm) 19110 9550 6370 4780 3820 3180 2390 1910 1590 1360 1190 1060 960 870 760 fn Vf (mm/rev) (mm/min) 0.003 0.006 0.009 0.011 0.014 0.016 0.021 0.027 0.034 0.040 0.046 0.051 0.055 0.062 0.071 230 230 220 210 210 210 200 210 220 220 220 220 210 220 210 n (rpm) 12740 6370 4250 3180 2550 2120 1590 1270 1060 910 800 710 640 580 510 N1 K3 1.5D x 0.2D < D3 mm: ae = 0.1D HF VH/U P4 ap x ae N TYPHOO HL MDTA Vc (m/min) N TYPHOO I SUH MIN G2 P3 K1 < 40 HRC N TYPHOO HRC /CO HSS-HSS DRILLS 700-1000 N/mm² SIDE MILLING SUTA P2 < 700 N/mm² N TYPHOO ALH LFTA Hardness/Rm N TYPHOO SUH C-SD-TA P1 N2 N3 N4 1.5D x 0.2D 100-120 fn Vf (mm/rev) (mm/min) 0.003 0.005 0.008 0.010 0.012 0.014 0.019 0.024 0.030 0.035 0.041 0.045 0.049 0.055 0.062 130 130 130 120 120 120 120 120 130 130 130 130 120 130 130 n (rpm) 35030 17520 11680 8760 7010 5840 4380 3500 2920 2500 2190 1950 1750 1590 1400 fn Vf (mm/rev) (mm/min) 0.005 0.009 0.013 0.017 0.021 0.025 0.033 0.042 0.052 0.061 0.070 0.078 0.085 0.095 0.108 640 640 610 590 580 580 570 580 610 610 610 610 590 600 600

OSAWA - katalog | KL-TECH s.r.o. | www.klte.cz | Page 340