OSAWA - katalog | KL-TECH s.r.o. | www.klte.cz

KL-TECH s.r.o | www.klte.cz G2 - General purpose - Square CUTTING PARAMETERS INFO G2310-G2311 N TYPHOO HTA TA-HTA-4 Material Group ISO 513 N TYPHOO PU-HPU P2 P3 K1 P4 M1 M2 P5 K2 M3 700-1000 N/mm² < 40 HRC ap x ae 0.5D x D 0.5D x D 0.5D x D Vc (m/min) 60-80 35-55 25-35 N TYPHOO ALH N TYPHOO HRC D (mm) n (rpm) fn Vf (mm/rev) (mm/min) 2 3 4 5 6 8 10 12 11150 7430 5570 4460 3720 2790 2230 1860 0.006 0.008 0.011 0.014 0.017 0.023 0.028 0.036 190 190 190 190 190 190 190 200 n (rpm) fn Vf (mm/rev) (mm/min) 7170 4780 3580 2870 2390 1790 1430 1190 0.005 0.007 0.010 0.012 0.014 0.019 0.024 0.031 100 100 100 100 100 100 100 110 n (rpm) N1 K3 < 700 N/mm² SLOTTING N2 N3 N4 0.5D x D 80-100 fn Vf (mm/rev) (mm/min) 4780 3180 2390 1910 1590 1190 960 800 0.004 0.006 0.008 0.011 0.013 0.017 0.021 0.027 60 60 60 60 60 60 60 60 n (rpm) fn Vf (mm/rev) (mm/min) 14330 9550 7170 5730 4780 3580 2870 2390 0.007 0.011 0.015 0.018 0.022 0.029 0.037 0.047 310 310 310 310 310 310 310 340 < D3 mm: ap = 0.2D Material Group ISO 513 N TYPHOO HL P1 P2 P3 K1 P4 M1 M2 P5 K2 M3 < 700 N/mm² 700-1000 N/mm² < 40 HRC 1.5D x 0.3D 1.5D x 0.3D 1.5D x 0.3D SUTA 70-90 D (mm) n (rpm) 2 3 4 5 6 8 10 12 12740 8490 6370 5100 4250 3180 2550 2120 45-65 fn Vf (mm/rev) (mm/min) 0.007 0.011 0.014 0.018 0.021 0.028 0.035 0.045 270 270 270 270 270 270 270 290 n (rpm) 8760 5840 4380 3500 2920 2190 1750 1460 160 160 160 160 160 160 160 170 n (rpm) 6370 4250 3180 2550 2120 1590 1270 1060 N3 N4 80-120 fn Vf (mm/rev) (mm/min) 0.005 0.008 0.011 0.013 0.016 0.021 0.026 0.034 N2 1.5D x 0.3D 30-50 fn Vf (mm/rev) (mm/min) 0.006 0.009 0.012 0.015 0.018 0.024 0.030 0.038 N1 K3 ap x ae SIDE MILLING LFTA Hardness/Rm Vc (m/min) C-SD-TA /CO HSS-HSS DRILLS Hardness/Rm N TYPHOO SUH N TYPHOO I SUH MIN P1 100 100 100 100 100 100 100 110 n (rpm) fn Vf (mm/rev) (mm/min) 15920 10620 7960 6370 5310 3980 3180 2650 0.009 0.014 0.018 0.023 0.027 0.037 0.046 0.059 440 440 440 440 440 440 440 470 < D3 mm: ae = 0.1D G2 G2312 MDTA P HF VH/U SIDE MILLING MEF ALU MEX UH -HSSP HSS/CO LS END MIL CARBIDE BURRS 334 Material Group ISO 513 P1 P2 K1 Hardness/Rm < 700 N/mm² 700-1000 N/mm² < 40 HRC ap x ae 1.5D x 0.2D 1.5D x 0.2D 1.5D x 0.2D Vc (m/min) 55-75 40-60 20-40 D (mm) n (rpm) 8 10 12 14 16 2590 2070 1730 1480 1290 P3 fn Vf (mm/rev) (mm/min) 0.020 0.025 0.032 0.037 0.045 160 160 170 160 170 P4 M1 M2 K2 n (rpm) 1990 1590 1330 1140 1000 fn Vf (mm/rev) (mm/min) 0.017 0.021 0.027 0.031 0.038 100 100 110 110 110 P5 M3 K3 n (rpm) 1190 960 800 680 600 N1 N2 N3 N4 1.5D x 0

OSAWA - katalog | KL-TECH s.r.o. | www.klte.cz | 页面 336