OSAWA - katalog | KL-TECH s.r.o. | www.klte.cz

KL-TECH s.r.o | www.klte.cz G2 - General purpose - Square CUTTING PARAMETERS INFO G2CSH3 N TYPHOO HTA TA-HTA-4 Material Group ISO 513 N TYPHOO PU-HPU P3 K1 P4 M1 M2 P5 K2 M3 < 40 HRC ap x ae 0.5D x D 0.5D x D 0.5D x D Vc (m/min) 80-100 50-70 30-50 SLOTTING D (mm) n (rpm) fn Vf (mm/rev) (mm/min) 1 2 3 4 5 6 8 10 12 14 16 18 20 28660 14330 9550 7170 5730 4780 3580 2870 2390 2050 1790 1590 1430 0.003 0.006 0.009 0.013 0.016 0.019 0.025 0.031 0.040 0.046 0.056 0.065 0.075 260 270 270 270 270 270 270 270 290 280 300 310 320 n (rpm) fn Vf (mm/rev) (mm/min) 19110 9550 6370 4780 3820 3180 2390 1910 1590 1360 1190 1060 960 0.003 0.005 0.008 0.011 0.013 0.016 0.021 0.027 0.034 0.039 0.048 0.055 0.064 150 150 150 150 150 150 150 150 160 160 170 180 180 n (rpm) N1 K3 700-1000 N/mm² N TYPHOO I SUH MIN N2 N3 N4 0.5D x D 80-120 fn Vf (mm/rev) (mm/min) 12740 6370 4250 3180 2550 2120 1590 1270 1060 910 800 710 640 0.002 0.005 0.007 0.009 0.012 0.014 0.019 0.023 0.030 0.035 0.042 0.049 0.056 90 90 90 90 90 90 90 90 100 90 100 100 110 n (rpm) fn Vf (mm/rev) (mm/min) 31850 15920 10620 7960 6370 5310 3980 3180 2650 2270 1990 1770 1590 0.004 0.008 0.012 0.016 0.020 0.024 0.033 0.041 0.052 0.060 0.073 0.085 0.098 370 390 390 390 390 390 390 390 410 410 440 450 470 < D3 mm: ap = 0.2D Material Group ISO 513 C-SD-TA CARBIDE BURRS 330 P4 M1 M2 P5 K2 M3 < 40 HRC Vc (m/min) 90-110 60-80 40-60 D (mm) n (rpm) 1 2 3 4 5 6 8 10 12 14 16 18 20 31850 15920 10620 7960 6370 5310 3980 3180 2650 2270 1990 1770 1590 fn Vf (mm/rev) (mm/min) 0.004 0.008 0.011 0.015 0.019 0.023 0.030 0.038 0.048 0.056 0.068 0.078 0.090 340 360 360 360 360 360 360 360 380 380 400 410 430 n (rpm) 22290 11150 7430 5570 4460 3720 2790 2230 1860 1590 1390 1240 1110 fn Vf (mm/rev) (mm/min) 0.003 0.006 0.010 0.013 0.016 0.019 0.026 0.032 0.041 0.047 0.057 0.066 0.077 200 210 210 210 210 210 210 210 230 230 240 250 250 n (rpm) 15920 7960 5310 3980 3180 2650 1990 1590 1330 1140 1000 880 800 N1 K3 1.5D x 0.3D < D3 mm: ae = 0.1D -HSSP HSS/CO LS END MIL 1.5D x 0.3D P UH P3 K1 700-1000 N/mm² MDTA MEX 1.5D x 0.3D G2 ALU P2 < 700 N/mm² SIDE MILLING MEF ap x ae SUTA /CO HSS-HSS DRILLS P1 Hardness/Rm LFTA HF VH/U P2 < 700 N/mm² N TYPHOO HRC N TYPHOO HL Hardness/Rm N TYPHOO SUH N TYPHOO ALH P1 N2 N3 N4 1.5D x 0.3D 110-120 fn Vf (mm/rev) (mm/min) 0.003 0.006 0.008 0.011 0.014 0.017 0.023 0.028 0.036 0.042 0.051 0.059 0.068 130 130 130 130 130 130 130 130 140 140 150 150 160 n (rpm) 38220 19110 12740 9550 7640 6370 4780 3820 3180 2730 2390 2120 1910 fn Vf (mm/rev) (mm/min) 0.005 0.010 0.015 0.020 0.024 0.029 0.039 0.049 0.062 0.072 0.088 0.101 0.117 540 560 560 560 560 560 560 560 600 590 630 640 670

OSAWA - katalog | KL-TECH s.r.o. | www.klte.cz | Page 332