African Mining November 2025 | Page 29

HEALTH AND SAFETY •
If the belt reaches into a tower or is exposed to the outdoors, this causes dust to be carried long distances by air currents into nearby communities, leading to potential violations.
Faulty methods for dealing with buildup include hitting the sides of the hopper with a mallet or poking at the obstruction from below to loosen it. In some operations, clogs are so common that specific spots for pounding are marked, and mallets are kept nearby for convenience. However, this is dangerous because it weakens the structural integrity of the vessel or chute, risking buckling. The ripple damage caused by pounding makes it easier for material to accumulate, reducing the time between clogs and increasing unscheduled downtime. Poking from below is even more hazardous, as a sudden discharge can send tons of material rushing out, risking injury to anyone nearby and damaging equipment below.
Recommendation: Air cannons strategically installed around the chute have nozzles aimed in the direction of the material flow. Powerful bursts of air are distributed across the surface inside the vessel, dislodging material and preventing buildup. The air cannons are supported by vibration units that ensure gates and narrow spouts on hoppers and chutes maintain proper flow before bridging begins. In many cases, vibration alone can manage most dry material flow, but changes in humidity that increase the stickiness of cargo and chute surfaces, along with fluctuations in production volumes, are much better handled by air cannons. clay, etc. Regulators measure fugitive particulate matter( PM) at the size of < 10 microns mass( μm) in volumes of > 50 micrograms( μg) per cubic meter( m3) over an eight-hour time weighted average( TWA). This is the volume and size determined to cause serious chronic lung issues in workers, and it doesn’ t just apply to RCS, it is any PM.
Dust emissions returning from the chute can result from uncontrolled airflow at the exit point. The emissions can also be caused by hitting rock boxes designed to slow the flow of material or by an unobstructed impact that causes turbulence.
Dust from carryback can permeate the area and spread emissions along the entire length of the belt return. If the belt reaches into a tower or is exposed to the outdoors, this causes dust to be carried long distances by air currents into nearby communities, leading to potential violations. Studies have shown that dust can be controlled through adequate cleaning at the discharge using Levels 1 – 3. Level one is a primary cleaner, level two a secondary cleaner and level three a tertiary cleaner.
Recommendation: Reconfiguring the chute’ s exit into a sloping scoop allows material to be slowed and loaded onto the next belt in a controlled, centred way with less turbulence. Air cannons installed along the chute are aimed with the material stream and can help direct airflow.
Conclusion Modern bulk handling industries are evolving and expanding daily. The demand for raw and processed materials for construction and manufacturing continues to rise. Increased production can alter throughput volumes and belt speeds, which directly impact spillage, carryback, clogging and dust.
Retroactively installing equipment that enhances both safety and efficiency should be a priority for any operator. Although the initial capital investment might be slightly higher, the return on investment( ROI) and benefits are not limited to fewer injuries but also include reduced labour costs for maintenance, fewer equipment replacements, improved compliance and an overall lower cost of operation. •
A sloped transfer chute reduces dust and mistracking but can clog, so air cannons mitigate buildup and assist material flow.
Discharge dust Emissions at the discharge zone can be found billowing out of the chute against the direction of the cargo stream or exiting the sides and bottom as it loosens from the belt’ s return side. Dust has become a highly regulated workplace and environmental concern which can lead to stiff fines and potential forced downtime if high volumes of respirable crystalline silica( RCS) is detected. RCS is found in nearly every substance pulled from the earth, but is prevalent in limestone, coal,
Introducing Daniel Marshall: Marshall received his Bachelor of Science degree in Mechanical Engineering from Northern Arizona University. With nearly 20 years at Martin Engineering, Marshall has been instrumental in the development and promotion of multiple belt conveyor products. He is widely known for his work in dust suppression and considered a leading expert in this area. Marshall has
Dan Marshall, process engineer, Martin Engineering.
published over two dozen articles covering various topics for the belt conveyor industry; presented at many conferences and is sought after for his expertise and advice. He was also one of the principal authors of Martin’ s FOUNDATIONS™, The Practical Resource for Cleaner, Safer, and More Productive Dust & Material Control, Fourth Edition. For more information, contact info @ martin-eng. com or visit www. martin-eng. com.
www. africanmining. co. za African Mining Publication African Mining African Mining • November 2025 • 27