African Mining July 2026 | Page 29

OPERATIONS •
Maintenance labour raises the cost of operation Running a system to failure due to an overstretched workforce will lead to more expensive and prolonged downtime. Inspection and maintenance of a conveyor system should be routine and performed regularly to prevent unscheduled downtime. It is easier said than done since belt cleaner tensioning is a continuous challenge for many operators. Under-tensioning leads to carryback and expedites the blade wear. In contrast, over-tensioning results in higher power costs, increased heat from friction, runs a higher risk of pull-through, and accelerates blade wear. After the lock-out / tag-out procedures, changing cleaners can be an ergonomically awkward task performed beneath a conveyor or inside the drop chute, often requiring two or more people and / or a confined space entry certification.
Safety Carryback increases safety risk as well as raising operational costs 2. Although it is strongly discouraged, operators continue to assign workers to clear spillage from around the system while the belt is running, shovelling the spillage back onto the moving conveyor, or into a skip or barrow – all of which drives up labour costs. If a worker comes into contact with the belt, the risk of an injury or fatality are high. In the bulk handling sector, working on or near moving conveyors remains a leading cause of workplace injuries and deaths. Besides the devastating price paid by a worker’ s family and colleagues in such circumstances, these incidents always result in costly fines, unscheduled downtime, and increased insurance premiums.
Anatomy of a discharge zone According to the Conveyor Equipment Manufacturers Association( CEMA),“ Conveyor belt cleaners are used to remove fugitive material, otherwise known as carryback, from the return side of the conveyor belt after the bulk material has been discharged. Ideally, this will be accomplished from within the chute works so that the removed carryback will pass onto the next system element.” 3 excessive vibration in the system, which may indicate mistracking or a change in the discharge stream. Lastly, always wear safety glasses and observe the operation of each component. Inspect the belt during a full rotation and note how the splice passes through the discharge process.
Conclusion In the punishing environment of bulk materials handling, many aspects of workplace safety and operational efficiency are directly tied to how clean the conveyor belt is. Since incidental contact with the high-speed belt has become the leading cause of conveyor injuries and fatalities, carryback is increasingly being scrutinised by inspectors from the US Occupational Safety and Health Administration( OSHA) and the US Mining Safety and Health Administration( MSHA). Eliminating the safety hazards associated with belt cleaning also brings benefits such as reduced unscheduled downtime, fewer equipment failures and lower operating costs. •
References:
1. T. Swinderman, A. Marti, L. Goldbeck, D. Marshall, & M. Strebel. Foundations: The Practical Resource for Cleaner, Safer, More Productive Dust & Material Control( Fourth Edition). Ch. 14, Pg. 201, Belt Cleaning. Worzalla Publishing Company, Stevens Point, WI, 2009.
2. U. S. Dept of Labor Statistics. Top 5 Events & Exposures. Occupational Safety and Health Administration( OSHA) Severe Injury Reports database. May, 2025. https:// www. osha. gov / severe-injury-reports
3. Conveyor Equipment Manufacturers Association [ CEMA ]. Classification of Applications for Bulk Material Conveyor Belt Cleaning. Pg. 3. Forward. Naples, FL, 2021.
By enclosing the discharge zone and extending the entry hood, operators can control airflow with dust curtains and return run seals. When retrofitting a new enclosure, installing a replaceable wear surface plate made of smooth reinforced metal on the impact wall of the transfer chute will reduce buildup and be easier to replace than the entire structure later. This design eliminates dust emissions from the capillary effect. As part of the enclosure, accessible inspection doors that offer a clear view of the equipment should be installed.
However, dust remains within the enclosure, so it is advisable to use shaft seals for bearings to prevent fouling. Once the appropriate primary, secondary and tertiary cleaners are installed and carryback is significantly reduced, operators will notice an increase in material flow through the transfer chute. It is recommended to install a dribble chute to ensure all captured material is handled. The dribble chute should include a vibrator or air cannon to ensure that dust and fines are reintegrated into the cargo stream and do not accumulate inside the enclosure.
Inspect and expect Inspecting a discharge zone can be time-consuming and requires all your senses. Listen for squeaking rollers and idlers, debris hitting the sides of the enclosure or the inspection door, and the scraping of accumulated materials on the pulley against the mainframe or enclosure. Smell for any metallic friction, as well as burning polyurethane or rubber. Feel for
The CleanScrape ® and its unique design require considerably less maintenance than other cleaners.
A fouled OEM tracking system, in this case, causing mistracking rather than remedying it. www. africanmining. co. za African Mining Publication African Mining
African Mining • July 2026 • 27