Indexable Drills
Application Data • Top Cut 4 ™
Top Cut 4 • Steel • 2 x D/3 x D • Feed Chart • Metric
Top Cut 4
Material
Group
Condition
S
1
U
I
S
2
U
I
S
3
U
I
P
S
4
U
I
S
5
U
I
S
6
U
I
Pocket
Seat Geometry Grade
P V36 WU25CH
C V36 WU40PH
P V36 WU40PH
C V36 WU40PH
P V36 WU40PH
C V36 WU40PH
P V34 WPK10CH
C V34 WU40PH
P V34 WU25CH
C V34 WU40PH
P V34 WU40PH
C V34 WU40PH
P V34 WPK10CH
C V34 WU40PH
P V34 WU25CH
C V34 WU40PH
P V34 WU40PH
C V34 WU40PH
P V34 WPK10CH
C V34 WU40PH
P V34 WU25CH
C V34 WU40PH
P V34 WU40PH
C V34 WU40PH
P V36 WU25CH
C V36 WU40PH
P V36 WU40PH
C V36 WU40PH
P V36 WU40PH
C V36 WU40PH
P V36 WU25CH
C V36 WU40PH
P V36 WU40PH
C V36 WU40PH
P V36 WU40PH
C V36 WU40PH
Insert Size B Insert Size C Insert Size D
TCF040203AC
TCF040204AP
12,00–13,99mm TCF060203BC
TCF050204BP
14,00–18,99mm TCF070304CC
TCF070306CP
19,00–23,99mm TCF090305DC
TCF080308DP
24,00–29,99mm
min Start max min Start max min Start max min Start max
0,06 0,08 0,10 0,08 0,10 0,13 0,10 0,12 0,15 0,11 0,13 0,16
0,06 0,08 0,10 0,08 0,10 0,13 0,10 0,12 0,15 0,11 0,13 0,16
0,06 0,08 0,10 0,08 0,10 0,13 0,10 0,12 0,15 0,11 0,13 0,16
0,06 0,08 0,10 0,08 0,12 0,15 0,10 0,13 0,16 0,11 0,14 0,17
0,06 0,08 0,10 0,08 0,12 0,15 0,10 0,13 0,16 0,11 0,14 0,17
0,06 0,08 0,10 0,08 0,12 0,15 0,10 0,13 0,16 0,11 0,14 0,17
0,08 0,11 0,15 0,10 0,12 0,16 0,11 0,14 0,18 0,12 0,15 0,20
0,08 0,11 0,14 0,10 0,12 0,15 0,11 0,14 0,16 0,12 0,15 0,18
0,08 0,11 0,14 0,10 0,12 0,15 0,11 0,14 0,16 0,12 0,15 0,18
0,08 0,11 0,15 0,10 0,12 0,16 0,11 0,14 0,18 0,12 0,15 0,20
0,08 0,11 0,14 0,10 0,12 0,15 0,11 0,14 0,16 0,12 0,15 0,18
0,08 0,11 0,14 0,10 0,12 0,15 0,11 0,14 0,16 0,12 0,15 0,18
0,06 0,08 0,10 0,08 0,10 0,14 0,10 0,12 0,15 0,11 0,13 0,16
0,06 0,08 0,10 0,08 0,10 0,14 0,10 0,12 0,15 0,11 0,13 0,16
0,06 0,08 0,10 0,08 0,10 0,14 0,10 0,12 0,15 0,11 0,13 0,16
0,06 0,08 0,10 0,08 0,10 0,14 0,10 0,12 0,15 0,11 0,13 0,16
0,06 0,08 0,10 0,08 0,10 0,14 0,10 0,12 0,15 0,11 0,13 0,16
0,06 0,08 0,10 0,08 0,10 0,14 0,10 0,12 0,15 0,11 0,13 0,16
NOTE: For 4 x D, it is highly recommended to start with feed and speed values reduced by 10% less than above recommendations.
For 5 x D, diameter range 12–23,99mm (insert sizes A to C), it is highly recommended to start with feed and speed values reduced by 20% less than
above recommendations.
For 5 x D, diameter range 24–68mm (insert sizes D to H), it is highly recommended to start with feed and speed values reduced by 15% less than
above recommendations.
For 4 x D and 5 x D, it is recommended to reduce the feed rate during entry and exit by 30–50%.
Condition: S = stable conditions,
U = unstable cutting conditions,
I = interrupted cutting conditions
Pocket Seat: P = periphery insert,
C = centre insert
V24
widia.com
Recommended Feed Rate by Diameter (mm/r)
Insert Size A