High-Performance Solid Carbide End Mills • VariMill ™
Application Data • Series 4727 • VariMill I ™
Series 4727 • VariMill
Side Milling (A)
Finishing
Roughing
TiAlN
A
Material
Group
P
M
S
H
A
Cutting Speed — vc
m/min
ae
min
max
ap
Cutting Speed — vc
m/min
ae
min
D1 — Diameter
max mm 12,0 16,0 20,0
1 Ap1 max 0,05 x D* 300 – 400 Ap1 max 0,2 x D 150 – 200 fz 0,083 0,101 0,114
2 Ap1 max 0,05 x D* 280 – 380 Ap1 max 0,2 x D 140 – 190 fz 0,083 0,101 0,114
3 Ap1 max 0,05 x D* 240 – 320 Ap1 max 0,2 x D 120 – 160 fz 0,070 0,087 0,101
4 Ap1 max 0,05 x D* 180 – 300 Ap1 max 0,2 x D 90 – 150 fz 0,062 0,077 0,088
5 Ap1 max 0,05 x D* 120 – 200 Ap1 max 0,2 x D 60 – 100 fz 0,056 0,070 0,081
6 Ap1 max 0,05 x D* 100 – 150 Ap1 max 0,2 x D 50 – 75 fz 0,047 0,057 0,065
1 Ap1 max 0,05 x D* 180 – 230 Ap1 max 0,2 x D 90 – 115 fz 0,070 0,087 0,101
2 Ap1 max 0,05 x D* 120 – 160 Ap1 max 0,2 x D 60 – 80 fz 0,056 0,070 0,081
3 Ap1 max 0,05 x D* 120 – 140 Ap1 max 0,2 x D 60 – 70 fz 0,047 0,057 0,065
1 Ap1 max 0,05 x D* 240 – 300 Ap1 max 0,2 x D 120 – 150 fz 0,083 0,101 0,114
2 Ap1 max 0,05 x D* 220 – 260 Ap1 max 0,2 x D 110 – 130 fz 0,070 0,087 0,101
3 Ap1 max 0,05 x D* 200 – 260 Ap1 max 0,2 x D 100 – 130 fz 0,056 0,070 0,081
1 Ap1 max 0,05 x D* 100 – 180 Ap1 max 0,2 x D 50 – 90 fz 0,070 0,087 0,101
2 Ap1 max 0,05 x D* 50 – 80 Ap1 max 0,2 x D 25 – 40 fz 0,070 0,087 0,101
3 Ap1 max 0,05 x D* 120 – 160 Ap1 max 0,2 x D 60 – 80 fz 0,037 0,046 0,054
4 Ap1 max 0,05 x D* 100 – 120 Ap1 max 0,2 x D 50 – 60 fz 0,052 0,064 0,074
1 Ap1 max 0,05 x D* 160 – 280 Ap1 max 0,2 x D 80 – 140 fz 0,062 0,077 0,088
*For cutting data above, use ae ) 0,8mm.
NOTE: Lower value of cutting speed is used for high stock removal applications or for higher hardness (machinability) within group.
Higher value of cutting speed is used for finishing applications or for lower hardness (machinability) within group.
Above parameters are based on ideal conditions. For smaller taper machining centres, please adjust parameters accordingly on >12mm diameters.
For finishing, increase feed per tooth by 20%.
O16
widia.com
K
ap
Recommended feed per tooth (fz = mm/th)
for side milling (A).
TiAlN