General Purpose Solid Carbide End Mills • Roughing/Finishing
Application Data • Series 423002 323002 423001 323001 • NINA ™
Series 423002 323002 423001 323001 • NINA
K30F-TICN K30F-DCF
TiCN TiAlN
Cutting Speed
— vc
m/min Cutting Speed
— vc
m/min
Side Milling (A)
and Slotting (B)
A
Material
Group
P
M
K
N
B
Recommended feed per tooth (fz = mm/th) for side milling (A).
For slotting (B), reduce fz by 20%.
D1 — Diameter
ap ae ap min – max min – max mm 2,0 3,0 4,0 5,0 6,0 8,0 10,0 12,0
0 0,75 x D 0,5 x D 0,5 x D 150 – 200 150 – 200 fz 0,014 0,021 0,028 0,036 0,044 0,060 0,072 0,083
1 0,75 x D 0,5 x D 0,5 x D 150 – 200 150 – 200 fz 0,014 0,021 0,028 0,036 0,044 0,060 0,072 0,083
2 0,75 x D 0,5 x D 0,5 x D 140 – 190 140 – 190 fz 0,014 0,021 0,028 0,036 0,044 0,060 0,072 0,083
3 0,75 x D 0,5 x D 0,5 x D 120 – 160 120 – 160 fz 0,011 0,017 0,023 0,030 0,036 0,050 0,061 0,070
4 0,75 x D 0,5 x D 0,5 x D 90 – 150 90 – 150 fz 0,010 0,016 0,021 0,027 0,033 0,045 0,054 0,062
1 0,75 x D 0,5 x D 0,5 x D 90 – 115 90 – 115 fz 0,011 0,017 0,023 0,030 0,036 0,050 0,061 0,070
2 0,75 x D 0,5 x D 0,5 x D 60 – 80 60 – 80 fz 0,009 0,014 0,019 0,024 0,029 0,040 0,048 0,056
1 0,75 x D 0,5 x D 0,5 x D 120 – 150 120 – 150 fz 0,014 0,021 0,028 0,036 0,044 0,060 0,072 0,083
2 0,75 x D 0,5 x D 0,5 x D 110 – 140 110 – 140 fz 0,011 0,017 0,023 0,030 0,036 0,050 0,061 0,070
1 0,75 x D 0,5 x D 0,5 x D 500 – 2000 500 – 2000 fz 0,020 0,030 0,040 0,050 0,060 0,080 0,100 0,120
2 0,75 x D 0,5 x D 0,5 x D 500 – 1500 500 – 1500 fz 0,018 0,027 0,036 0,045 0,054 0,072 0,090 0,108
5 0,75 x D 0,5 x D 0,5 x D 250 – 1000 250 – 1000 fz 0,018 0,027 0,036 0,045 0,054 0,072 0,090 0,108
NOTE: Lower value of cutting speed is used for high stock removal applications or for higher hardness (machinability) within group.
Higher value of cutting speed is used for fi nishing applications or for lower hardness (machinability) within group.
Series 423004 423003 • NINA
K30F-DCHP
Side Milling (A)
and Slotting (B)
A
Material
Group
P
M
K
N
Recommended feed per tooth (fz = mm/th) for side milling (A).
For slotting (B), reduce fz by 20%.
AlTiN
B
Cutting Speed — vc
m/min
D1 — Diameter
ap ae ap min – max mm 4,0 5,0 6,0 8,0 10,0 12,0
0 1 x D 0,5 x D 1 x D 150 – 200 fz 0,028 0,036 0,044 0,060 0,072 0,083
1 1 x D 0,5 x D 1 x D 150 – 200 fz 0,028 0,036 0,044 0,060 0,072 0,083
2 1 x D 0,5 x D 1 x D 140 – 190 fz 0,028 0,036 0,044 0,060 0,072 0,083
3 1 x D 0,5 x D 1 x D 120 – 160 fz 0,023 0,030 0,036 0,050 0,061 0,070
4 1 x D 0,5 x D 1 x D 90 – 150 fz 0,021 0,027 0,033 0,045 0,054 0,062
1 1 x D 0,5 x D 1 x D 90 – 115 fz 0,023 0,030 0,036 0,050 0,061 0,070
2 1 x D 0,5 x D 1 x D 60 – 80 fz 0,019 0,024 0,029 0,040 0,048 0,056
1 1 x D 0,5 x D 1 x D 120 – 150 fz 0,028 0,036 0,044 0,060 0,072 0,083
2 1 x D 0,5 x D 1 x D 110 – 140 fz 0,023 0,030 0,036 0,050 0,061 0,070
3 1 x D 0,5 x D 1 x D 110 – 130 fz 0,019 0,024 0,029 0,040 0,048 0,056
1 1 x D 0,5 x D 1 x D 500 – 2000 fz 0,040 0,050 0,060 0,080 0,100 0,120
2 1 x D 0,5 x D 1 x D 500 – 1500 fz 0,036 0,045 0,054 0,072 0,090 0,108
3 1 x D 0,5 x D 1 x D 250 – 1000 fz 0,036 0,045 0,054 0,072 0,090 0,108
NOTE: Lower value of cutting speed is used for high stock removal applications or for higher hardness (machinability) within group.
Higher value of cutting speed is used for fi nishing applications or for lower hardness (machinability) within group.
widia.com
P9
Application Data • Series 423004 423003 • NINA