High-Performance Solid Carbide End Mills • Hard Materials
Application Data • Series D618 • Vision Plus ™
Series D618 • Vision Plus
Material
Group
P
H
Side Milling (A) TiAlN
A Cutting Speed — vc
m/min
ap ae min
Recommended feed per tooth (fz = mm/th) for side milling (A).
D1 — Diameter
max mm 3,0 4,0 5,0 6,0 8,0 10,0 12,0 16,0 20,0
3 2 x D 0,15 x D 120 – 160 fz 0,019 0,026 0,033 0,040 0,055 0,067 0,077 0,096 0,111
4 2 x D 0,15 x D 90 – 150 fz 0,017 0,024 0,030 0,036 0,049 0,059 0,069 0,084 0,097
1 2 x D 0,15 x D 80 – 140 fz 0,017 0,024 0,030 0,036 0,049 0,059 0,069 0,084 0,097
2 2 x D 0,15 x D 70 – 120 fz 0,013 0,018 0,022 0,027 0,037 0,044 0,051 0,063 0,071
3 2 x D 0,1 x D 60 – 90 fz 0,010 0,014 0,018 0,021 0,029 0,035 0,041 0,051 0,059
4 2 x D 0,05 x D 50 – 70 fz 0,007 0,009 0,012 0,014 0,019 0,023 0,027 0,034 0,039
NOTE: Lower value of cutting speed is used for high stock removal applications or for higher hardness (machinability) within group.
Higher value of cutting speed is used for fi nishing applications or for lower hardness (machinability) within group.
For better surface fi nish, reduce feed per tooth.
Above parameters are based on ideal conditions. For smaller taper machining centres, please adjust parameters accordingly on diameters >12mm.
Series 422837 422831 • Vision Plus
K10UF-DCHP
Side Milling (A)
Cutting Speed — vc
m/min
A
Material
Group
P
H
Recommended feed per tooth (fz = mm/th) for side milling (A).
AlTiN
ap ae min
D1 — Diameter
max mm 6,0 8,0 10,0 12,0 16,0 20,0 25,0
3 1,5 x D 0,2 x D 120 – 160 fz 0,040 0,055 0,067 0,077 0,096 0,111 0,125
4 1,5 x D 0,2 x D 90 – 150 fz 0,036 0,049 0,059 0,069 0,084 0,097 0,107
1 1,5 x D 0,2 x D 80 – 140 fz 0,036 0,049 0,059 0,069 0,084 0,097 0,107
2 1,5 x D 0,15 x D 60 – 80 fz 0,027 0,037 0,044 0,051 0,063 0,071 0,078
3 1,5 x D 0,1 x D 50 – 70 fz 0,021 0,029 0,035 0,041 0,051 0,059 0,067
4 1,5 x D 0,05 x D 40 – 60 fz 0,014 0,019 0,023 0,027 0,034 0,039 0,044
Application Data • Series 422837 422831 • Vision Plus ™
widia.com
O203
NOTE: Lower value of cutting speed is used for high stock removal applications or for higher hardness (machinability) within group.
Higher value of cutting speed is used for fi nishing applications or for lower hardness (machinability) within group.
For better surface fi nish, reduce feed per tooth.
For Series 422831, ap max = 2,5 x D by 50% ae.
Above parameters are based on ideal conditions. For smaller taper machining centres, please adjust parameters accordingly on diameters >12mm.