High-Performance Solid Carbide End Mills • Hard Materials
Application Data • Series 7N01 • Vision Plus ™ Micro
Series 7N01 • Vision Plus Micro
H
ap ae min
3 0,04 x D 0,04 x D 432
4 0,04 x D 0,04 x D 324
1 0,03 x D 0,03 x D 2 0,03 x D 3 0,02 x D 4 0,02 x D max mm 0,5 0,6 0,8 1,0 1,5 2,0 2,5 3,0
– 576 fz 0,012 0,015 0,020 0,025 0,038 0,051 0,064 0,078
– 540 fz 0,012 0,014 0,019 0,023 0,035 0,047 0,059 0,072
288 – 504 fz 0,012 0,014 0,019 0,023 0,035 0,047 0,059 0,072
0,03 x D 252 – 432 fz 0,009 0,011 0,014 0,018 0,027 0,036 0,045 0,054
0,02 x D 216 – 324 fz 0,007 0,008 0,011 0,014 0,021 0,028 0,035 0,043
0,02 x D 180 – 252 fz 0,005 0,006 0,007 0,009 0,014 0,019 0,024 0,028
Profile Milling
P
H
ae min
3 0,1 x D 0,05 x D 300
4 0,1 x D 0,05 x D 225
1 0,07 x D 0,1 x D 2 0,05 x D 3 0,03 x D 4 0,03 x D
H
D1 — Diameter
max mm 0,5 0,6 0,8 1,0 1,5 2,0 2,5 3,0
- 400 fz 0,008 0,010 0,013 0,017 0,025 0,034 0,043 0,052
- 375 fz 0,008 0,009 0,012 0,016 0,023 0,031 0,040 0,048
200 - 350 fz 0,008 0,009 0,012 0,016 0,023 0,031 0,040 0,048
0,04 x D 175 - 300 fz 0,006 0,007 0,009 0,012 0,018 0,024 0,030 0,036
0,03 x D 150 - 225 fz 0,005 0,006 0,007 0,009 0,014 0,019 0,024 0,028
0,03 x D 125 - 175 fz 0,003 0,004 0,005 0,006 0,009 0,012 0,016 0,019
K10UF-DCHP
Recommended feed per tooth (fz = mm/th) for 3D milling/profiling (A) — Roughing
AlTiN
Cutting Speed — vc
m/min
A
Material
Group
Recommended feed per tooth (fz = mm/th) for 3D milling/profiling (A) — Semi-Finishing
AlTiN
ap
Profile Milling
P
K10UF-DCHP
Cutting Speed — vc
m/min
A
Material
Group
D1 — Diameter
D1 — Diameter
ap ae min 3 0,2 x D 0,1 x D 216 4 0,2 x D 0,1 x D 162 1 0,15 x D 0,1 x D 144 2 0,1 x D 0,075 x D 126 - 216 fz 0,003 0,004 0,005 0,006 0,009 0,012 0,015 0,018
3 0,05 x D 0,05 x D 108 - 162 fz 0,002 0,003 0,004 0,005 0,007 0,009 0,012 0,014
4 0,05 x D 0,05 x D 90 - 126 fz 0,002 0,002 0,002 0,003 0,005 0,006 0,008 0,009
max mm 0,5 0,6 0,8 1,0 1,5 2,0 2,5 3,0
- 288 fz 0,004 0,005 0,007 0,008 0,013 0,017 0,021 0,026
- 270 fz 0,004 0,005 0,006 0,008 0,012 0,016 0,020 0,024
- 252 fz 0,004 0,005 0,006 0,008 0,012 0,016 0,020 0,024
NOTE: Please use reference table for correction of vc based on average degrees of the mould. See page O205.
widia.com
P
Recommended feed per tooth (fz = mm/th) for 3D milling/profiling (A) — Finishing
AlTiN
Cutting Speed — vc
m/min
A
Material
Group
K10UF-DCHP
O169
Profile Milling