14 Contrails Magazine / September, 2016
Initial Setup.
Plane Options – Set ground equip as required.
Parking Brake – Set on.
BAT – On
STBY POWER – Auto
EXT PWR – Set On if available.
L & R Bus tie – Auto
L & R Utility bus – On
L, C, R IRS – NAV
Emergency Lights – Armed & Guarded.
Lights – Cabin, Position, Wing And Logo.
Cabin & Cargo Temperature – Set as needed.
Trim AIR – On.
L & R Recirculation Fan – On.
L & R Pack – Auto
L, C, R Isolation Valves – On.
Load Plane.
Plane Options – Set ground equipment as required.
Before Startup.
IRS Panel – Check
L & R Yaw Damper – On.
L & R ELEC ENG CONT – On
HYD PUMPS – Set All On.
APU GEN – On.
GEN CONT – L & R On.
ENG Start – Both.
Cargo Heat – All On.
Window Heat – All On.
Cabin Signs – On.
Cabin Altitude – LDG ALT.
L ENG, APU, R ENG – On.
APU Startup.
APU GEN – On.
APU Bleed Air Valve – On.
External Lights – Beacon On.
APU – Start
APU EGT about 640.
RPM 100.
EXT PWR – Off.
Parking Brake – Set.
Push Back And Engine Start Up.
Parking Brake – Set.
IRS Panel – Alignment Complete.
HYD Pumps – On.
GEN CONT – On.
ENG START – Both.
Cabin Signs – Auto.
L, C, R Isolation – On.
Bleed Air Valves – L ENG, APU, R ENG On.
FUEL PUMPS – On.
Lights – Taxi Nosegear On.
L & R Pack – Off.
Start Push Back.
Engine Start Selector – GND.
At 20% N2 – Fuel Control RUN.
Parking Brake – On.
L & R Pack – AUTO.
APU BLEED AIR Valve – Off.
APU – Off.
Before Taxi Setup.
Parking Brake – Set.
IRS Panel – Check.
HYD PUMPS – On.
BUS TIE – Auto.
UTILITY BUS – On.
GEN CONT – On.
APU – Off.
Cargo Heat – On.
Window Heat – On.
Cabin Signs – On.
Cabin & Cargo Temperature – Set.
Trim AIR – On.
L & R Recirc Fan – On.
L & R Pack – Auto.
Bleed Air Valves – L & R ENG On.
L, C, R Isolation – Off.
ANTI ICE – On.
Internal Lights – As Needed.
Before Takeoff.
Flaps – Set.
Trim – Set.
Speed Brake – Off.
Auto Brake – RTO.
MCP – Verify IAS, HDG, ALT.
External Lights – Landing And Anti Collision On.
Transponder – Set TA/RA
Takeoff.
Parking Brake – Off.
Thrust Reverse – Off.
Speed Brake – Off.
After Takeoff.
Landing Gear – Up.
A P Engage – Engage Autopilot
Climb.
Altimiters – Set QNH 1013 or Altimiter 2992.
EFIS Control Panel – Set Range as needed.
Cabin Pressure – Check DIFF, ALT And RATE.
External Lights – Landing Off.
Cabin Signs – As Needed.
Cruise.
Flight Instruments – Altitude, Speed, Heading.
Engine Instruments – Check EPR, N1, EGT.
FUEL QTY – Check Fuel Balance, Total QTY And Temperature.
Cabin Pressure – Check DIFF, ALT, RATE.
FMC PROG Page – Check T/D Distance.
Before Descent.
Approach And Landing Procedure – Check.
FMC RTE Page – Enter arrival procedure.
FMC Approach Page – Enter FLAP Speed And Verify VREF.
Auto Brake – As Needed.
EFIS Control Panel – Set DH According To Charts.
ILS Panel – Set FREQ And HDG.
Radios – Set as needed for approach.
Cabin Signs – On.
Descent.
MCP Altitude – Set as cleared by ATC.
External Lights – Landing On.
Altimiters – Set QNH or Altimiter as needed.
Radios – Set as needed for Tower.
Taxi Procedure – Check.
Before Landing.
ILS – Verify that the ILS is turned and identified.
MCP – Set APP On.
Landing Gear – Down.
Flaps – As Needed.
MCP – Set Missed Approach Altitude.
Speed Brake – Armed.
EFIS Control Panel – Set Range 10.
Auto Land – Verify Auto Land Status at 500 Feet.
Landing.
Throttle – Idle.
Speed Brake – Down.
Thrust Reverse – Reverse.
After Landing.
Thrust Reverse – At 60 Knots Reduce To Idle.
A/P Engage – Disconnect.
A/T ARM – Off.
Auto Brake – Off.
Taxi To Gate.
External Lights – Landing And Anti Collision Off.
L & R Flight Directors – Off.
Flaps – Up.
Speed Brake – Off.
Transponder – As Needed.
APU Bleed Air Valvue – On.
L, C, R Isolation – On.
APU GEN – On.
APU – Start.
Engine Shutdown.
Parking Brake – Set.
External Lights – Taxi And Nose Gear Off.
Anti Ice – Off.
Fuel Pumps – Off.
EXT PWR – On.
APU – Off.