FYI
What You Need:
• 1590G Enclosure (link: http://goo.gl/
IAY5z8)
• Dual 18650 Battery Sled (link: http://
goo.gl/mBeMMU)
• 510 Connector (link: http://goo.gl/
AhY1lT)
• Pushbutton Fire Switch (link: http://
goo.gl/dVmJYp)
• High Amp Mosfet (link: http://goo.gl/
xuou4g)
• 15k Ohm Resistor (link: http://goo.gl/
ZLgnkb)
• Master On/Off Switch (link: http://goo.
gl/0DLEpM)
• Two 15 Amp Resettable Fuses (link:
http://goo.gl/R7KB4J)
• Magnets for Enclosure – (link: http://
goo.gl/bPMrvd)
• 16g Electrical Wire (link: http://goo.
gl/5NHBxi)
• 20g Electrical Wire (link: http://goo.gl/
K2i3PX)
Tools You Might Need:
• Soldering Iron (link: http://goo.
gl/18esRk)
• Solder (link: http://goo.gl/IU2DO1)
• Flux Paste (link: http://goo.gl/OEEev1)
• Epoxy (link: http://goo.gl/0gMmBh)
Alright that’s everything, now let’s start
building! The first thing I like to do with
every box mod, is to sand and even out
the enclosure. Many of these project
boxes come with slightly slanted sides.
This will cause your atomizer to sit at a
slant. If this doesn’t bother you, then you
can skip the sanding step.
To sand the enclosure, I simply use
regular sandpaper and a flat surface.
I then slowly sand each edge of the
enclosure until I am satisfied with the
even angles. Again, this is optional and
can be skipped.
Laying It All Out
After I get my enclosure exactly the way
I want, I will now plan out the placement
of each individual part. I usually start
with the battery sled and modify it
if necessary. Typically, this involves
sanding and rounding out the bottom
right corner of the sled.
Next you need to decide where you
would like to place your 510 connector.
I usually like it in the centre of my box
mods, but you can move it to the right or
left depending on your own preferences.
Now comes the fire switch; like many box
mods, I place my switch on the top left
of the enclosures. Again this is personal
preference and you can place it on any
side. If you decide to follow the same
layout of my box mod that I show in the
video on my website, then you will be left
with a perfect spot for your MOSFET and
on/off switch.
Drilling Out The Holes
You can now move onto drilling out all
the necessary holes for your unregulated
box mod. For this project, all we need to
drill is the hole for the 510 connector and
the fire switch.
Many of you have asked how I drill out
my holes for box mods. I have dedicated
a whole video on this topic. The title
of that video is “MOD TIPS #02 – How
to Drill Holes for Box Mods” which
I definitely encourage you to watch
(the URL of which is https://youtu.be/
EG3D6LtAm6s ).
Wiring Everything Up!
Here is the simply wiring diagram that
I have created just for you. This is the
diagram that we will follow to complete
our unregulated box mod.
Please watch the video accompanying
this tutorial (URL here: https://youtu.be/
qr3V5A4pK9Y) for more detailed wiring
instructions. It is not possible for me to
put all the steps in writing.
MOSFET Wiring
We want to first take a look at the
VAPOUROUND MAGAZINE WINTER EDITION 157