1. Anchor
Channel Systems
2. HAC
Portfolio
3. HAC
Applications
5. Base material
6. Loading
the EDGE Lite, EDGE, and EDGE S plate. These components
increase the perpendicular concrete edge breakout strength.
The S brackets improves the shear steel performance
(perpendicular shear) of HAC. Dimensions of the S bracket are
given in Figures 2.2.16.8 and 2.2.16.9.
Head diameter
1
d 1
l A
Maximum anchor
spacing s max
Net bearing area of the
anchor head
A brg
l pl
Overall length of the EDGE
Lite or EDGE plate rebars l R
Bar effective cross-sectional
area
Minimum rebar spacing
(mm) (31.0)
in 1.65
(mm) (41.9)
in 0.0796
Maximum rebar spacing
C/C distance between the outer
rebar and the outer anchor
(33,125)
in 0.77
(mm) (19.50)
in 0.21
(mm) (5.30)
in 0.11
(mm) (2.75)
in 0.11
(mm) (2.75)
in 0.98
(mm) (25)
in 0.36
(mm) (9.03)
in 0.77
(mm) (19.50)
in 3.09 2.62
(78.50) (66.5)
in 3.94
(100)
in 9.84
(mm) (250)
in 2 0.400
(mm 2 ) (258)
A se
s min,R
s max,R
x R
Distance from the end of the
EDGE Lite or EDGE plate to the
center of the installation hole 1 d i
Edge distance (from outside
face of EDGE Lite or EDGE
plate to center of HAC anchor c a1
Development length of
rebars l d
in 1.97 2.36 3.94
(mm) (50) (60) (100)
in 0.99 1.97 (mm) (25) (50)
in
Channel length + 2(x pl )
(mm)
in 18.11 23.62
(mm) (460) (600)
in 0.39 0.47
(mm) (10) (12)
in 2 0.12 0.18
(mm 2 ) (78.54) (113.1)
in 3.74 3.74
(mm) (95) (95)
in 3.75 5.71
(mm) (95) (145)
in 0.295 0.295
(mm) (7.50)
(7.50)
in 0.40
(mm) (10)
in
(mm)
in
(mm)
Figure 2.2.16.6 — Isometric view of HAC-T EDGE Lite
and HAC-T EDGE.
Figure 2.2.16.7 — Isometric view of fixture that
attaches the EDGE Lite or EDGE plate to HAC-T.
As specified
l R - c a1 + t pl
1 N
ail hole diameter is equal to 6 mm (0.25 in.)
(mm) (mm)
d b
0.24
(6.00)
Figure 2.2.16.5 a — Dimensions of the
anchor channel of HAC-T EDGE Lite, HAC-T
EDGE, and HAC-T S EDGE.
HBC-T
s chb
Nail hole location 3 x nail
3 x bolt diameter
in
(mm)
1” offset from anchor
(25.4 offset from anchor)
Figure 2.2.16.8 — HAC-T EDGE Lite and HAC-T EDGE dimensions, section
and elevation view.
Figure 2.2.16.5 b — HAC end and nail
hole distance.
HAC-T EDGE C has reinforcing bars that are located one reinforcing bar diameter
below the bottom base of the anchor channel profile to avoid clashing with the
reinforcing bars of the opposite corner channel (HAC-T EDGE). The plate is taller
and thicker.
Figure 2.2.16.9 — HAC-T EDGE C dimensions, section and elevation view.
Cast-In Anchor Channel Product Guide, Edition 1 • 02/2019
79
1 T
he head diameter is the inner diameter of the hexagonal shaped head, and does not fully reflect the cross sectional area of
the anchor head.
2 H AC-T EDGE C is the matching corner channel and has the same anchor channel as the intermediate HAC EDGE. The shear
confinement plate has different geometry.
* Effective embedment depth not covered by ICC ESR-3520.
3 Nail hole diameter is 4 mm (0.16 in.)
Minimum channel bolt
spacing
78
Length of the EDGE Lite or
EDGE plate
(97.5)
1.22
Matching channel bolt
x pl
0.20 (5.00) s min
Projection of the EDGE
Lite or EDGE plate 0.16 (4.00) Minimum anchor
spacing h pl
in (mm)
Anchor length
d 2
Height of the EDGE
Lite or EDGE plate
EDGE C
Anchor shaft diameter
x min
t pl
Rebar nominal diameter
3.84
in
(mm )
Thickness of the EDGE Lite
or EDGE plate
EDGE
Minimum end spacing
t nom,b
0.14
(3.50)
4
HAC-T50
Channel lip thickness
(bottom)
t nom,t
in (mm)
4
Units
Channel lip thickness
(top)
f
(94)
(109.2)
Symbol
Channel lip flange
thickness
d
(106) (mm)
Criteria
Channel profile opening
I y
(mm) 4.31
Anchor Channel
Channel profile moment
of inertia
b ch
*3.70
in
Table 2.2.16.2 — Geometric parameters of HAC-T EDGE Lite and
HAC-T EDGE
Channel profile width
h ch
4.17
14. Design
Example
Channel profile height
h nom
in
13. Field Fixes
Nominal embedment
depth
t h
HAC-T50 EDGE Lite
HAC-T50 EDGE
HAC-T50 S EDGE
12. Instructions
for Use
Thickness of the anchor
head
h ef,min
11. Best
Practices
Min. effective
embedment depth
Units
10. Design
Software
Anchor Channel
Symbol
9. Special Anchor
Channel Design
EDGE Lite
Table 2.2.16.1 — Geometric parameters for HAC-T EDGE Lite, HAC-T EDGE,
and HAC-T S EDGE 2
Criteria
8. Reinforcing
Bar Anchorage
Table 2.2.16.1 provides geometric parameters for the anchor
channels that compose the HAC-T EDGE product line. Tables
2.2.16.2 and 2.2.16.3 provide geometric information about
7. Anchor Channel
Design Code
HAC-T50 EDGE Lite, HAC-T50 EDGE, and HAC-T50 S EDGE
utilize HAC-T50 with rounded head anchors. HAC-T50 is
covered by ICC ESR-3520. HAC-T50 with reduced embedment
depth [h ef = 3.70” (94 mm)] is not covered by ESR-3520.
4. Design
Introduction