STANDARDS AND REGULATIONS
SANS 1808-10 Water supply and distribution system components. Part 10: Copper alloy check valves (spring-loaded). 2005 1.02
SANS 1808-13 Water supply and distribution system components. Part 13: Diaphragm valves. 2009 1.02
SANS 1808-15 Water supply and distribution system components. Part 15: Mechanical back-flow prevention devices. 2011 1.02
SANS 1808-16 Water supply and distribution system components. Part 16: Drinking fountain taps. 2017 1.03
SANS 1808-18 Water supply and distribution system components. Part 18: uPVC gate valves. 2010 1.02
SANS 1808-24 Water supply and distribution system components. Part 24: Gas-operated water heaters. 2010 1.02
SANS 1808-30 Water supply and distribution system components. Part 30: Laboratory water taps. 2004 1.01
SANS 1808-31 Water supply and distribution system components. Part 31: Automatic control valves. 2010 1.03
SANS 1808-32 Water supply and distribution system components. Part 32: Float valves (equilibrium type). 2010 1.03
SANS 1808-35 Water supply and distribution system components. Part 35: Electronically operated taps and valves. 2010 1.02
SANS 1808-37 Water supply and distribution system components. Part 37: Single-control mixer taps (plastics). 2005 1.02
SANS 1808-44 Water supply and distribution system components. Part 44: Pipe saddles. 2010 1.03
SANS 1808-45 Water supply and distribution system components. Part 45: Pipe repair clamps. 2013 1.03
SANS 1808-53 Water supply and distribution system components. Part 53: Drain cocks for hot-water storage containers. 2012 1.03
SANS 1808-58 Water supply and distribution system components. Part 58: In-line strainers. 2010 1.03
SANS 1808-66 Water supply and distribution system components. Part 66: Demand type water taps. 2005 1.02
SANS 1835 1.02
SANS 1848 Ductile iron pipes, fittings, accessories and their joints, for use in high and low-pressure systems 2017
for potable and foul water.
Geyser drip trays.
2011 SANS 1849 Butterfly valves for general purposes. 2008 1.01
SANS 1857 Copper alloy gate valves - light duty. 2005 1.01
SANS 4427 Polyethylene (PE) pressure pipes for water supply - specifications. 2008 1.00
SANS 4633 Rubber seals - joint rings for water supply, drainage and sewerage pipelining. Specification for material. 2008 1.00
SANS 52566-4 2010 1.00
2009 1.00
2014 2.02
SANS 9454-1 Small wastewater treatment systems for up to 50PT. Part 4: Septic tanks assembled in situ from
prefabricated kits.
Specification for glass-fibre reinforced cisterns of one piece and sectional construction for the
storage above ground of cold water.
Safety of household and similar electrical appliances. Part 2-73: Particular requirements for
fixed immersion heaters.
Soft soldering fluxes - classification and requirements. Part 1: Classification, labelling and packaging. 1990 1.00
SANS 9455-1 Soft soldering fluxes - test method. Part 1: Non-volatile matter, gravimetric method. 1990 1.00
SANS 9455-10 Soft soldering fluxes - test method. Part 10: Flux efficacy tests - solder spread method. 1998 1.00
SANS 9455-12 Soft soldering fluxes - test method. Part 12: Steel tube corrosion tests. 1992 1.00
SANS 9455-13 Soft soldering fluxes - test method. Part 13: Determination of flux spattering. 1996 1.00
SANS 9455-14 Soft soldering fluxes - test method. Part 14: Assessment of tackiness of flux. 1991 1.00
SANS 9455-15 Soft soldering fluxes - test method. Part 15: Copper corrosion test. 1996 1.00
SANS 9455-16 Soft soldering fluxes - test method. Part 16: Flux efficacy tests - wetting balance method. 1998 1.00
SANS 9455-17 2009 1.00
SANS 15874-1, 2, 3, 5 & 7 Soft soldering fluxes - test method. Part 17: Surface insulation resistance combination tests and
electrochemical migration test of flux residues.
Plastic piping systems (PP) for hot and cold-water installations in buildings (all parts adhered to). 2004 1.00
SANS 15875-1, 2, 3, 5 Plastic piping systems (PE-X) for hot and cold-water installations in buildings (all parts adhered to). 2004 2.00
SANS 15875-7 Plastics piping systems (PP) for hot and cold water installations - Cross-linked polyethylene (PE-
X). Part 7: Guidance for the assessment of conformity.
Plastic piping systems (PB) for hot and cold-water installations in buildings (parts 1,2,3,5). 2010 1.00
SANS 53280
SANS 60335-2-73
SANS 15876-1, 2, 3, 5
SANS 15876-7
SANS 21003-1, 2, 3, 5
SANS 21003-7
SANS 22391-1, 2, 3, 5
1.05
2005 1.00
Plastics piping systems for hot and cold water installations - Polybutylene (PB). Part 7: Guidance 2010
for the assessment of conformity
Multilayer piping systems for hot and cold-water installations in buildings (parts 1,2,3,5).
2008 1.00
Multilayer piping systems for hot and cold water installations inside buildings. Part 7: Guidance
for the assessment of conformity
Plastic piping systems (PE-RT) for hot and cold-water installation of raised temperature (parts 1,2,3,5). 2011 1.00
2008 1.00
1.00
REFERENCE
Information sourced from the SABS website as at 24 October 2018. Please note that this information is provided as a guide only.
The onus is on the individual to check for updates during the time of reference. Technical committees meet often, which may
result in amendments during the year.
www.plumbingafrica.co.za
117
Plumbing Africa Directory 2019