OSAWA - katalog | KL-TECH s.r.o. | www.klte.cz

KL-TECH s.r.o | www.klte.cz MDTA - General purpose - Square CUTTING PARAMETERS INFO MDTACS3 Material Group ISO 513 P1 P2 P3 K1 P4 M1 M2 P5 K2 M3 Hardness/Rm < 700 N/mm² 700-1000 N/mm² < 40 HRC ap x ae 0.5D x D 0.5D x D 0.5D x D Vc (m/min) SLOTTING 80-100 D (mm) n (rpm) 1 2 3 4 5 6 8 10 12 14 16 18 20 28660 14330 9550 7170 5730 4780 3580 2870 2390 2050 1790 1590 1430 50-70 fn Vf (mm/rev) (mm/min) 0.004 0.008 0.011 0.014 0.018 0.021 0.028 0.035 0.044 0.052 0.059 0.066 0.072 330 330 320 310 300 300 300 300 320 320 320 310 310 n (rpm) 0.003 0.007 0.009 0.012 0.015 0.018 0.023 0.030 0.037 0.044 0.050 0.056 0.061 190 190 180 170 170 170 170 170 180 180 180 180 180 n (rpm) N2 N3 N4 TYPHOO N PU-HPU 0.003 0.006 0.008 0.011 0.013 0.016 0.021 0.026 0.033 0.039 0.045 0.050 0.054 110 110 110 100 100 100 100 100 100 110 110 110 100 n (rpm) fn Vf (mm/rev) (mm/min) 35030 17520 11680 8760 7010 5840 4380 3500 2920 2500 2190 1950 1750 0.005 0.010 0.014 0.019 0.023 0.027 0.036 0.046 0.057 0.067 0.077 0.086 0.093 530 530 500 490 480 480 470 480 500 500 510 500 490 < D3 mm: ap = 0.2D Material Group ISO 513 P1 P2 P3 K1 P4 M1 M2 P5 K2 M3 < 700 N/mm² 700-1000 N/mm² < 40 HRC ap x ae 1.5D x 0.3D 1.5D x 0.3D 1.5D x 0.3D SIDE MILLING < D3 mm: ae = 0.1D 80-100 D (mm) n (rpm) 1 2 3 4 5 6 8 10 12 14 16 18 20 28660 14330 9550 7170 5730 4780 3580 2870 2390 2050 1790 1590 1430 50-70 fn Vf (mm/rev) (mm/min) 0.005 0.009 0.013 0.017 0.021 0.025 0.033 0.042 0.053 0.062 0.071 0.079 0.086 400 400 380 370 360 360 350 360 380 380 380 380 370 n (rpm) 19110 9550 6370 4780 3820 3180 2390 1910 1590 1360 1190 1060 960 230 230 210 210 210 200 200 210 210 220 220 210 210 n (rpm) 12740 6370 4250 3180 2550 2120 1590 1270 1060 910 800 710 640 N2 N3 N4 TYPHOO N SUH TYPHOO N ALH TYPHOO N HRC TYPHOO N SUH MIN I TYPHOO N HL C-SD-TA LFTA 100-120 fn Vf (mm/rev) (mm/min) 0.003 0.007 0.010 0.013 0.016 0.019 0.025 0.032 0.040 0.047 0.053 0.059 0.064 1.5D x 0.3D 30-50 fn Vf (mm/rev) (mm/min) 0.004 0.008 0.011 0.015 0.018 0.021 0.028 0.036 0.045 0.053 0.061 0.067 0.073 N1 K3 Hardness/Rm Vc (m/min) TYPHOO N TA-HTA-4 HTA 100-120 fn Vf (mm/rev) (mm/min) 12740 6370 4250 3180 2550 2120 1590 1270 1060 910 800 710 640 0.5D x D 30-50 fn Vf (mm/rev) (mm/min) 19110 9550 6370 4780 3820 3180 2390 1910 1590 1360 1190 1060 960 N1 K3 130 130 130 120 120 120 120 120 130 130 130 130 120 n (rpm) 35030 17520 11680 8760 7010 5840 4380 3500 2920 2500 2190 1950 1750 fn Vf (mm/rev) (mm/min) 0.006 0.012 0.017 0.022 0.027 0.033 0.043 0.055 0.069 0.081 0.093 0.103 0.112 630 630 600 590 580 570 560 580 600 600 610 600 590 SUTA HSS-HSS /CO DRILLS G2 MDTA HF VH/U P MEF ALU MEX UH HSS/CO -HSSP END MIL LS CARBIDE BURRS 371

OSAWA - katalog | KL-TECH s.r.o. | www.klte.cz | Página 373