OSAWA - katalog | KL-TECH s.r.o. | www.klte.cz

KL-TECH s. r. o | www. klte. cz

G2- General purpose- Square

CUTTING PARAMETERS

G2210-G2211

INFO

Material Group ISO 513

P1 P2 K1 P3 P4 M1 M2 K2 P5 M3 K3 N1 N2 N3 N4

TYPHOON TA-HTA-4HTA

SLOTTING

< D3 mm: ap = 0.2D

SIDE MILLING

< D3 mm: ae = 0.2D

Hardness / Rm < 700 N / mm ² 700-1000 N / mm ² < 40 HRC ap x ae 0.5D x D 0.5D x D 0.5D x D 0.5D x D

Vc( m / min) 70-90 45-65 30-50 80-120

D( mm) n( rpm) fn( mm / rev)

Vf( mm / min) n( rpm) fn( mm / rev)

Vf( mm / min)

2	12740	0.007	180	8760	0.006	100	6370	0.005	70	15920	0.009	290
3	8490	0.010	170	5840	0.009	100	4250	0.008	60	10620	0.013	280
4	6370	0.014	180	4380	0.012	100	3180	0.011	70	7960	0.018	290
5	5100	0.018	180	3500	0.015	110	2550	0.014	70	6370	0.023	300
6	4250	0.023	190	2920	0.019	110	2120	0.017	70	5310	0.029	310
8	3180	0.030	190	2190	0.026	110	1590	0.023	70	3980	0.039	310
10	2550	0.035	180	1750	0.030	100	1270	0.026	70	3180	0.046	290
12	2120	0.041	170	1460	0.035	100	1060	0.031	70	2650	0.053	280

Material Group ISO 513

P1 P2 K1 P3 P4 M1 M2 K2 P5 M3 K3 N1 N2 N3 N4

Hardness / Rm < 700 N / mm ² 700-1000 N / mm ² < 40 HRC ap x ae 1.5D x 0.5D 1.5D x 0.5D 1.5D x 0.5D 1.5D x 0.5D

Vc( m / min) 70-90 45-65 30-50 80-120

D( mm) n( rpm) fn( mm / rev)

Vf( mm / min) n( rpm) fn( mm / rev)

Vf( mm / min)

2	12740	0.008	210	8760	0.007	130	6370	0.006	80	15920	0.011	350
3	8490	0.012	200	5840	0.010	120	4250	0.009	80	10620	0.016	330
4	6370	0.017	210	4380	0.014	130	3180	0.013	80	7960	0.022	350
5	5100	0.022	220	3500	0.018	130	2550	0.016	80	6370	0.028	360
6	4250	0.027	230	2920	0.023	130	2120	0.020	90	5310	0.035	370
8	3180	0.036	230	2190	0.031	130	1590	0.027	90	3980	0.047	370
10	2550	0.042	210	1750	0.036	120	1270	0.032	80	3180	0.055	350
12	2120	0.049	210	1460	0.042	120	1060	0.037	80	2650	0.064	340

TYPHOON PU-HPU

TYPHOON SUH

TYPHOON ALH

TYPHOON HRC

TYPHOON SUH MINI

TYPHOON HL

C-SD-TA

LFTA

SUTA

HSS-HSS / CO DRILLS

Material Group ISO 513

P1 P2 K1 P3 P4 M1 M2 K2 P5 M3 K3 N1 N2 N3 N4

Hardness / Rm < 700 N / mm ² 700-1000 N / mm ² < 40 HRC

DRILLING

< D3 mm: ap = 0.5D ap x ae D X D D X D 0.5D X D D X D Vc( m / min) 60-80 40-60 25-45 70-110

D( mm) n( rpm) fn( mm / rev)

Vf( mm / min) n( rpm) fn( mm / rev)

Vf( mm / min)

2	11150	0.004	90	7960	0.004	60	5570	0.003	40	14330	0.005	160
3	7430	0.006	90	5310	0.005	50	3720	0.005	30	9550	0.008	150
4	5570	0.008	90	3980	0.007	60	2790	0.006	40	7170	0.011	160
5	4460	0.011	100	3180	0.009	60	2230	0.008	40	5730	0.014	160
6	3720	0.014	100	2650	0.011	60	1860	0.010	40	4780	0.018	170
8	2790	0.018	100	1990	0.015	60	1390	0.014	40	3580	0.023	170
10	2230	0.021	90	1590	0.018	60	1110	0.016	30	2870	0.027	160
12	1860	0.025	90	1330	0.021	60	930	0.018	30	2390	0.032	150

MDTA

HF VH / UP

MEF

ALU

MEX

HSS / CO-HSSP END MILLS

CARBIDE BURRS

325

OSAWA - katalog | KL-TECH s.r.o. | www.klte.cz | Seite 327