Nine9 | KL-TECH s.r.o. | www.klte.cz Nine9 | Page 53

KL-TECH s.r.o | www.klte.cz
30°
45°
60°
Cutting Data
NEW
Before you start, please pay attention the following conditions
• The downward feed rate of the Z-axis should be reduced to 50% of the table feed rate.
• Cutting fluid emulsion is recommended for engraving on steel, stainless steel, Al and Al-alloy;
blown cooled air is recommended for engraving on cast iron and plastic.
• The tool shank runout should be below 0.01 mm.
• Shrink fit chucks, hydraulic chuck and high precision spring collet chucks are recommended.
• Pre-balance the tool holder minimum G6.3/10,000 R.P.M. is necessary.
30° Engraving X060 Insert >>
f (mm/rev.)
Work Material
S
(r.p.m.)
Radius Angled Form
Grade of
Insert
Radius Form
X060A30W010R X060A30W020R X060A30R010
X060A30R020
Carbon steel C<0.3% 0.0010 ~ 0.006 0.001 ~ 0.010 0.0010 ~ 0.010 0.002 ~ 0.015 NC2032
Carbon steel C>0.3% 0.0010 ~ 0.005 0.001 ~ 0.008 0.0010 ~ 0.008 0.002 ~ 0.012 NC2032
Alloy steel 0.0005 ~ 0.005 0.001 ~ 0.006 0.0010 ~ 0.005 0.002 ~ 0.010 NC2032, NC2035
0.0005 ~ 0.004 0.001 ~ 0.006 0.0010 ~ 0.005 0.002 ~ 0.010 NC2032
Stainless Steel
Cast iron
8000 ~ 40000
0.0010 ~ 0.005 0.001 ~ 0.006 0.0010 ~ 0.006 0.002 ~ 0.010 NC2032
Aluminum 0.0010 ~ 0.008 0.001 ~ 0.012 0.0010 ~ 0.010 0.002 ~ 0.020 XP9001
Copper, Brass 0.0010 ~ 0.008 0.001 ~ 0.012 0.0010 ~ 0.010 0.002 ~ 0.020 XP9001
Hardened Steel Up to56 HRC 0.0005 ~ 0.003 0.001 ~ 0.005 0.0005 ~ 0.003 0.002 ~ 0.006 NC2035
f (mm/rev.)
Work Material
S
(r.p.m.)
Radius Angled Form
Grade of
Insert
Radius Form
X060A45W010R X060A45W020R X060A45R010
X060A45R020
Carbon steel C<0.3% 0.001 ~ 0.010 0.002 ~ 0.012 0.001 ~ 0.010 0.002 ~ 0.015 NC2032
Carbon steel C>0.3% 0.001 ~ 0.008 0.002 ~ 0.010 0.001 ~ 0.008 0.002 ~ 0.012 NC2032
Alloy steel 0.001 ~ 0.006 0.002 ~ 0.010 0.001 ~ 0.006 0.002 ~ 0.010 NC2032, NC2035
0.001 ~ 0.006 0.002 ~ 0.008 0.001 ~ 0.006 0.002 ~ 0.010 NC2032
0.001 ~ 0.008 0.002 ~ 0.010 0.001 ~ 0.008 0.002 ~ 0.010 NC2032
Aluminum 0.001 ~ 0.010 0.002 ~ 0.015 0.001 ~ 0.012 0.002 ~ 0.020 XP9001
Copper, Brass 0.001 ~ 0.010 0.002 ~ 0.015 0.001 ~ 0.012 0.002 ~ 0.020 XP9001
Hardened Steel Up to56 HRC 0.001 ~ 0.004 0.002 ~ 0.006 0.001 ~ 0.004 0.002 ~ 0.006 NC2035
Stainless Steel
Cast iron
8000 ~ 40000
60° Engraving X060 Insert >>
f (mm/rev.)
Work Material
S
(r.p.m.)
Radius Angled Form
Grade of
Insert
Radius Form
X060A60W010R X060A60W020R X060A60R010
X060A60R020
Carbon steel C<0.3% 0.001 ~ 0.010 0.002~0.012 0.001~0.010 0.002~0.015 NC2032
Carbon steel C>0.3% 0.001 ~ 0.010 0.002~0.010 0.001~0.010 0.002~0.012 NC2032
Alloy steel 0.001 ~ 0.008 0.002~0.010 0.001~0.008 0.002~0.010 NC2032, NC2035
0.001 ~ 0.006 0.002~0.008 0.001~0.006 0.002~0.010 NC2032
0.001 ~ 0.010 0.002~0.010 0.001~0.010 0.002~0.010 NC2032
Aluminum 0.001 ~ 0.012 0.002~0.015 0.001~0.015 0.002~0.020 XP9001
Copper, Brass 0.001 ~ 0.012 0.002~0.015 0.001~0.015 0.002~0.020 XP9001
Hardened Steel Up to56 HRC 0.001 ~ 0.005 0.002~0.006 0.001~0.005 0.002~0.006 NC2035
Stainless Steel
Cast iron
8000 ~ 40000
Nine9 Cutting Tool & Tool Holders 51
45° Engraving X060 Insert >>