LAMINA - katalog | KL-TECH s.r.o. | www.klte.cz Lamina | Page 259

KL-TECH s.r.o | www.klte.cz
MACHINING CONDITIONS - MILLING - DEPTH OF CUT AND FEED
RDMW 1003 M0
Material
Group
P
RDMW 10T3 M0
Lamina
Gr. N° Material
Examples
Non Alloyed 1 C35, Ck45,
1020, 1045,
1060, 28Mn6
Low Alloyed 2 42CrMo4,
St50, Ck60,
4140, 4340,
100Cr6
3 X40CrMoV5,
H13, M42, D3,
S6-5-2, 12Ni19
Grey 7 GG20, GG40, EN-
GJL-250,
N030B
Malleable
& Nodular 8 GGG40,
GGG70,
50005
High Alloyed
K
Steel
11
H
Chilled Cast Iron
White Cast Iron
RDMW 1204 M0
Material
Group
Non Alloyed
P
Low Alloyed
Ni-Hard 2
G-X300CrMo15
Lamina
Gr. N° Material
Examples
1 C35, Ck45,
1020, 1045,
1060, 28Mn6
2 42CrMo4,
St50, Ck60,
4140, 4340,
100Cr6
X40CrMoV5,
H13, M42, D3,
S6-5-2, 12Ni19
Grey 7 GG20, GG40, EN-
GJL-250,
N030B
Malleable
& Nodular 8 GGG40,
GGG70,
50005
K
Steel
11
H
Chilled Cast Iron
White Cast Iron
DOC
[mm]
Hardness
125 HB
190 HB
250 HB
180 HB
230 HB
280 HB
350 HB
220 HB
280 HB
320 HB
350 HB
150 HB
200 HB
250 HB
150 HB
200 HB
250 HB
45 HRc
50 HRc
55 HRc
400 HB
55 HRc
Feed
[mm/z]
max min max DOC Feed
0.50 2.50 0.18 0.70 1.00 0.39
0.50 2.50 0.15 0.50 1.80 0.12 0.50 2.50 0.18 0.70 1.00 0.39
0.50 2.50 0.15 0.62 1.00 0.34
0.30 0.90
0.70
0.60
0.70
0.60 0.10 0.40
0.35
0.31
0.40
0.31 0.50
0.40
0.30
0.40
0.30 0.24
0.22
0.20
0.24
0.20
X100 CrMo13,
440C,
G-X260NiCr42
Ni-Hard 2
G-X300CrMo15
0.55
0.48
0.48
0.40
1.00
0.80
0.34
0.31
0.31
0.27
RXMW 1204 M0
DOC
[mm]
Hardness
125 HB
190 HB
250 HB
180 HB
230 HB
280 HB
350 HB
220 HB
280 HB
320 HB
350 HB
150 HB
200 HB
250 HB
150 HB
200 HB
250 HB
45 HRc
50 HRc
55 HRc
400 HB
55 HRc
Suggested Starting
Parameters
min
RDMW 12T3 M0
3
High Alloyed
258
X100 CrMo13,
440C,
G-X260NiCr42
RXMW 10T3 M0
min
0.30
0.30
0.30
Feed
[mm/z]
max
4.00
3.00
4.00
3.00
2.00
1.50
2.00
1.50
min
0.27
0.25
0.23
0.20
Suggested Starting
Parameters
max
0.70
0.65
0.50
0.65
0.57
0.52
0.50
0.57
0.52
0.50
0.47
DOC
1.50
1.50
1.00
1.00
0.30 3.00 0.20 0.80 2.00
0.30 2.50 0.20 0.60 1.50
0.30 1.00
0.80
0.50
1.00
0.50 0.18 0.38
0.34
0.30
0.38
0.34 0.50
Feed
0.60
0.60
0.50
0.60
0.55
0.50
0.50
0.55
0.50
0.45
0.80
0.70
0.60
0.50
0.55
0.60
0.38
0.34
0.30
0.38
0.34
The depth of cut and feed rate tables are for the geometry and corner radius specified above the table.
Refer to cutting speed tables on page 226 for recommended materials per grade.