LAMINA - katalog | KL-TECH s.r.o. | www.klte.cz Lamina | Page 223

KL-TECH s.r.o | www.klte.cz
MACHINING CONDITIONS - TURNING - DEPTH OF CUT AND FEED
TNUX 160408 L
TNUX 160408 R
Material
Group
Non Alloyed
P
Low Alloyed
High Alloyed
M
Lamina
Gr. N°
1
2
3
X40CrMoV5,
H13, M42, D3,
S6-5-2, 12Ni19
190 HB
280 HB
280 HB
320 HB
180 HB
6 410, X6Cr17,
17-4PH, 430 200 HB
7 GG20, GG40, EN-
GJL-250,
N030B 150 HB
Grey Ti based 10
11
Chilled Cast Iron
White Cast Iron
Aluminium
12
240 HB
310 HB
42 HRc
200 HB
0.21
0.50
4.00
3.00
max
1.80
0.45 1.50
0.45
0.18 0.40
0.18
240 HB
250 HB
Stellite 21 350 HB
T40 -
TiAl6V4 -
400 HB
G-X300CrMo15 55 HRc
AlSi12 130 HB
3.00
0.32
1.00 2.70 0.40 1.20 2.50 0.30
0.35 0.80 2.20 0.28
0.30
5.00 0.20 0.40 1.20
1.00 3.00 0.25
0.22
0.50 4.00 0.18 0.35 0.80 2.50 0.24
0.50 5.00
4.00 0.18 0.40 0.70 2.50
2.20 0.20
0.50 5.00 0.15 3.00 0.35
0.50 5.00 0.15 0.50 1.50
1.30
1.20 3.00 0.30
0.50 3.00 0.20 0.35 0.70 2.00 0.28
0.40
0.35
0.30
0.25
0.20
0.25
0.20
0.60 0.80
0.70
0.60
0.40
0.30
0.40
0.30
1.80
0.50
50 HRc
55 HRc
Feed
0.38
0.35
0.33
0.50
45 HRc
Ni-Hard 2 DOC 3.00
0.60
0.55
250 HB
Inconel 700
Suggested Starting
Parameters
1.20
150 HB
200 HB
Amax
[mm 2 ]
0.50 0.21
250 HB
Incoloy 800
X100 CrMo13,
440C, G-X260NiCr42
4.00
3.50
350 HB
Ferritic &
Martensitic 9
0.50
220 HB
290 HB
Fe, Ni &
Co based
5.00
5.00
350 HB
X2CrNiN23-4,
S31500
GGG40, GGG70,
50005
0.50
180 HB
230 HB
5 8
min
250 HB
Duplex Malleable
& Nodular
Feed
[mm/rev]
max
125 HB
304, 316,
X5CrNi18-9
H
222
42CrMo4,
St50, Ck60,
4140, 4340,
100Cr6
min
4
Steel
NF
C35, Ck45,
1020, 1045,
1060, 28Mn6
DOC
[mm]
Hardness
Austenitic
K
S
Material
Examples
0.50
0.50
3.50
3.00
2.50
2.00
1.50
2.00
1.50
6.00
0.20
0.11
0.20
2.00
1.80
2.00
2.00
1.50
1.00
1.50
1.00
3.00
0.33
0.30
0.25
0.20
0.18
0.15
0.40
The depth of cut and feed rate tables are for the geometry and corner radius specified above the table.
Refer to cutting speed tables on pages 186 and 187 for recommended materials per grade.