LAMINA - katalog | KL-TECH s.r.o. | www.klte.cz Lamina | Page 198

KL-TECH s.r.o | www.klte.cz
MACHINING CONDITIONS - TURNING - DEPTH OF CUT AND FEED
SCMT 09T304 NN
Material
Group
Non Alloyed
P
Low Alloyed
High Alloyed
1
2
3
42CrMo4,
St50, Ck60,
4140, 4340,
100Cr6
X40CrMoV5,
H13, M42, D3,
S6-5-2, 12Ni19
min
125 HB
190 HB
280 HB
320 HB
Duplex 5 290 HB
Ferritic &
Martensitic 6 410, X6Cr17,
17-4PH, 430 200 HB
GG20, GG40, EN-
GJL-250,
N030B 150 HB
Malleable
& Nodular 8
Fe, Ni &
Co based 9
Ti based 10
Steel
11
H
GGG40, GGG70,
50005
310 HB
42 HRc
200 HB
max
0.72
0.25 0.62
0.23 0.58
0.23
0.10
0.21
0.21
3.30
0.3
0.09
2.70
0.18
0.16
240 HB
250 HB
Stellite 21 350 HB
T40 -
TiAl6V4 -
DOC Feed
2.50 0.18
0.60
0.58
0.48
0.14
2.50
0.13
0.43
0.48
0.38
0.31
0.38
2.10 0.10
2.10 0.10
0.08 0.21 0.3 2.70 0.08 0.16 0.24 2.10 0.08
0.21 0.38 2.10 0.09
0.18 0.31 1.90 0.08
2.50 0.18
2.50 0.13
1.60 0.10
0.3
3.30
2.70
0.08
0.31
2.50
0.09
3.30
0.08
0.77
0.3 4.00 0.08 0.23 0.3 3.30 0.08 0.21 0.3 2.70 0.09 0.17 0.31
0.3 2.70 0.09 0.18 0.38
0.16 0.31
0.72
0.58
250 HB
Inconel 700
Suggested Starting
Parameters
0.3
150 HB
200 HB
Amax
[mm 2 ]
0.26
250 HB
Incoloy 800
X100 CrMo13,
440C, G-X260NiCr42
0.11
2.70
350 HB
240 HB
3.30
0.3
220 HB
280 HB
min
3.30
350 HB
X2CrNiN23-4,
S31500
7
0.3
180 HB
230 HB
Feed
[mm/rev]
max
4.00
250 HB
180 HB
K
NF
C35, Ck45,
1020, 1045,
1060, 28Mn6
DOC
[mm]
Hardness
304, 316,
X5CrNi18-9
Grey
S
Material
Examples
4
Austenitic
M
Lamina
Gr. N°
0.48
1.60
0.14
0.10
45 HRc 2.40 0.14 0.24 1.80 0.10
50 HRc 2.00 0.12 0.20 1.40 0.08
0.10 0.16 1.10 0.06
55 HRc
0.3
1.90
0.05
Chilled Cast Iron Ni-Hard 2 400 HB 2.10 0.14 0.20 1.40 0.10
White Cast Iron G-X300CrMo15 55 HRc 1.90 0.10 0.16 1.10 0.06
AlSi12 130 HB 0.35 0.84 2.50 0.23
Aluminium
12
0.3
5.30
0.10
The depth of cut and feed rate tables are for the geometry and corner radius specified above the table.
Refer to cutting speed tables on pages 186 and 187 for recommended materials per grade.
197