Product Data Sheet
OMNI PLANE DIFFUSER PANEL
PART 1 GENERAL
2.4 Edge profile shall be: Square.
1.1 Work in this section shall be subject to drawings, general
conditions, schedules, addenda and other contract
documents.
2.5 Panel finish shall be __________________________
______________ (specify finish manufacturer, pattern,
color and specifier). Finish shall be applied directly over
the face and edges of the panel and returned to the back
of the panel to provide a full finished edge. All corners are
fully tailored.
1.2 The extent of the acoustical panels is shown on the
drawings and in the schedules.
1.3 Submit _______ (select quantity) samples of each type
of acoustical panel as shown on the drawings and in
schedules and include appropriate technical information
including test data and maintenance instructions. Submit
__________ (select quantity) fabric selector cards from
manufacturer’s standard finishes, or designer specified
finishes.
1.4 Acoustical panels shall be installed according to
manufacturer’s recommendations and instructions.
1.5 Installation of acoustical panels shall not begin until all wet
work (plastering, concrete, etc.) is completed and dry.
Building shall be properly enclosed and under standard
occupancy conditions (temperature of
60-85°F and not more than 70% relative humidity) before
installation begins.
2.6 Mounting shall be: Z-Bar to Z-Bar or Lay-in for ceilings,
Z-Clip or impaling clip / perimeter adhesive for walls.
Adhesive, miscellaneous fasteners, (i.e. nails, screws, etc.)
and standard continuous wall leveling angle are to be
supplied by the contractor.
2.7 Acoustical Performance – panels shall have a minimum
NRC of _____ (please specify) in accordance with ASTM
C-423 (Type “A” Mounting).
2.8 Flammability – All panel components shall have a Class
“A” flame spread rating of 25 or less in accordance with
ASTM E-84.
Thank you for choosing Conwed Designscape|Wall
Technology for your acoustical needs.
1.6 The contractor shall be responsible for the examination
and acceptance of all surfaces and conditions prior to the
acoustical panel installation.
The information provided above is correct to the best of our
knowledge at time of printing. We reserve the right to make
changes without prior notification.
1.7 Substitutions or changes will only be permitted by prior
approval by the architect.
DISCLAIMER OF LIABILITY
Technical information contained herein is furnished without charge or obligation and is
given and accepted at recipient’s sole risk. Because conditions of use may vary and are
beyond our control, Owens Corning makes no representation about, and is not responsible
or liable for the accuracy or reliability of data associated with particular uses of any product
described herein. Nothing contained in this bulletin shall be considered a recommendation.
PART 2 MATERIALS
2.1 Acoustical ceiling panels shall be: The Omni Plane Diffuser
Panel as manufactured by Conwed Designscape|Wall
Technology, 800 Gustafson Road, Ladysmith, WI 54848.
Phone (800) 932-2383, fax (800) 833-4798.
2.2 Acoustical Panels shall be constructed of a composite
core with two layers of dimensionally stable rigid
fiberglass of 6-7 pcf density separated by a proprietary
vinyl layer. Thickness (choose one) 1” or 2”.
2.3 Sizes: ______ width and _______ high or as shown on
drawings. Standard maximum size is 36”x 60” for ceilings
and 48” wide x 120” high for wall panels. Custom sizes
within these limitations are standard. Panels are to be
manufactured according to field dimensions supplied by
the installing contractor. Standard tolerances are ± 1/16”
in width and length.
+YWXEJWSR 6SEH
0EH]WQMXL;MWGSRWMR
T: 1-800-932-2383
F: 1-800-833-4798
www.conweddesignscape.com
4YF2S %4VMRXIH MR 97%%TVMP
3[IRW 'SVRMRK%PP 6MKLXW 6IWIVZIH
0))( MW E VIKMWXIVIH XVEHIQEVO SJ 97+VIIR &YMPHMRK 'SYRGMP