Protecting Your Investment and Preparing for Next Season MARVIN JOLES
IN THE MIX
Winterizing Your Sealcoating Equipment:
Protecting Your Investment and Preparing for Next Season MARVIN JOLES
A s the sealcoating season comes to an end across much of the country, contractors begin shifting their focus from completing jobs to preparing their businesses for winter. While it’ s tempting to park the equipment, close the shop doors, and take a well-deserved vacation to a Florida beach, there’ s one final responsibility that shouldn’ t be overlooked: properly winterizing your equipment. At Wis-Coat, operating in Wisconsin means dealing with freezing temperatures for several months. Including the sneaky nights in October that drop below freezing for one night only … and cause a major headache. Over the years, I’ ve learned that taking the time to properly shut down and winterize equipment can make a significant difference in maintenance costs, equipment longevity, and how smoothly the following season begins. Winterization isn’ t just about protecting equipment from freezing. It’ s about protecting your investment.
Start with a thorough cleaning. One of the most important steps is thoroughly cleaning your sealcoating equipment with water before storing it. Multiple rinses are ideal, as thicker deposits of sealer can build up. Run it until it’ s pretty clear. Leftover sealer can settle, harden, and create problems inside tanks, pumps, hoses, valves, and spray systems. Depending on the equipment and material being used, manufacturers may recommend circulating water through the system, using an approved cleaning solution, or following a specific shutdown procedure.
Pay particular attention to the wand, filters, strainers, and valves. Especially the areas in between valves. These smaller components are often overlooked but can create frustrating problems when starting up in the spring if they are fractured or split.
Protect Pumps, Hoses, and Plumbing
In colder climates, water left inside pumps, hoses, and plumbing can freeze, expand, and cause expensive damage. Drain water from all components where possible, including low points in the plumbing system. I often forget about the water tank and broom boxes on our rigs. Depending on your equipment, an approved winterizing solution may be necessary to protect components that cannot be completely drained. For the most part at Wis- Coat, we use an RV antifreeze that you can find at almost any store or auto parts store.
Always follow the manufacturer’ s recommendations regarding antifreeze or winterizing products. Not every solution is compatible with every pump, seal, or material. Once spring hits, inspect hoses and pipes for cracking, wear, and weak connections. Replacing a questionable hose during the offseason is much easier than dealing with a failure in the middle of a busy workday in the spring, when you are supposed to be hitting the ground running.
Don’ t Forget Engines and Mechanical Components
Sealcoating equipment involves more than tanks and pumps.
Engines, compressors, hydraulic systems, bearings, and other mechanical components deserve attention. Change engine oil when recommended, inspect belts, lubricate grease points, and check fluid levels. The more petroleum we have where it’ s supposed to be over the winter months, the better.
Fuel-powered equipment should be stored according to the engine manufacturer’ s guidelines, including appropriate fuel treatment or draining procedures. Batteries should also be maintained or removed and stored appropriately to prevent deterioration during extended periods of inactivity. If we don’ t take the batteries out of the sealcoat trucks, they will for sure be dead in the spring and some just flat out won’ t be any good. That can be an expensive thing to deal with and can be avoided. If you use a pressure washer or plate compactor, don’ t forget they likely have water in them as well.
Use the Offseason to Evaluate Your Equipment
Winterization provides an excellent opportunity to assess the overall condition of your equipment. I often end the season wide open and flying the burning plane into the landing area to get across the finish line. Patched up and needing attention. Take inventory of worn parts, damaged components, and recurring maintenance issues. Make a list of repairs or improvements that can be completed before spring. It’ s also a good time to evaluate whether your equipment is still meeting the needs of your operation or whether upgrades could improve productivity next season. Conference and expo season is over the winter months, and it’ s a great time to shop if you are in need.
A Better Start Next Spring
As contractors, we spend considerable time thinking about production, efficiency, and profitability during the season. Equipment maintenance deserves that same attention. A few hours spent properly winterizing equipment can prevent thousands of dollars in repairs, reduce unexpected spring downtime, and help ensure you’ re ready when the first opportunities arrive in spring.“ The next season doesn’ t start when the weather warms up. It starts with how you finish this one.” As always, if you have any questions, insight or criticisms about this article or anything in it, please feel free to email me at marvinjoles @ gmail. com and, of course, reach out to me using any form of social media(@ inthemixmj). Listen to the‘ In The Mix with Marvin Joles’ podcast on Spotify or Apple Podcasts, or watch on YouTube. Visit www. inthemixmj. com to learn more. Asphalt is Opportunity.-Marvin
Marvin Joles is the owner of Wis-Coat Asphalt Maintenance. Visit his website at https:// marvinjoles. com.
[ 30 ] www. callape. com 1.800.210.5923